Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi eveyone,
I try to using ncs DTM example , but I get error reset with following message. what is the meaning for MPSL ASSERT: 2, 80 , I cannot found any related info...
How do I get to the point that I can print a simple "Hello World" on a terminal from a custom board?
I have a custom board the is based on the nrf5340. Specifically, I am...
Hi,
we are working on a nrf52840 based device, which has an external mx25r16 flash (via SPI), having 3 partitions for: secondary-image, mcu-scatch-partition and application...
The informational section of Lesson 6 uses the "Controller/Target" nomenclature for I2C devices, but question 2 of the Quiz requires the use of "Master/Slave" nomenclature...
Hello,
I'm trying to achieve a rather simple program with three steps.
I initialize the SAADC to sample three channels (currently I only have one setup)
I "arm/prepare...
Hi,
In NRF52840, We use LFXO Oscillator (KJ3270001). We did not connect any crystal or Oscillator for HFCLK.
1) What will be the clock source for SPI and I2C communications...
Hi,
We've been working on taking the distance measurements from the nrf_dm sample and displaying them on a waveshare e-paper 2.13 in display. We've been able to get both...
Hi,
I have a project for nRF52 in VS Code. The project was able to compile and everything worked fine. However, after about a month, I reopened the project and now there...
I am developing LTE-M software on nRF9160. Previously, I checked that it runs well with nRF9160DK. Now I try it with my own board.
First, only for testing, I made following...
Hi, I'm trying to set up wireless audio stream using 2 nRF52832 Dev Kits and SGTL5000 audio boards. SDK: nRF5 SDK 17.1.0 For the wireless protocol I've used ESB, and the program...
Hi, I've been trying to modify some of the nRF5 SDK 17.1.0 BLE HID examples to make the nRF appear as a BLE HID Braille Display, that would be recognized in Android's TalkBack...
Hello,
I'm modifying the code of Wireless timer synchronization among nRF5 devices blog to use RTC instead of two TIMERs. I started with the code on Git for SDK 16. Writing...
Hello,
I am trying to interface a TCA9548A Multiplexer on my custom board. I am able to set up the channels and read the channel status' with device_get_binding successfully...
