after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi
I use nRF7002-DK and sdk version as v2.5.2,download lesson8 exercise 3 solution and build was error as below log, which parts am I miss?
build config as below
...
Hello,
I a working on a project that uses the nRF5340 CCM peripheral (Network core) in an asynchronous mode. That is, I encrypt PDUs prior to scheduling them for transmission...
I want to configure my setup for secure boot and enable TFM and encrypted application images for firmware update. I am using nRF sdk version 2.5.0. My board is nRF9160. Now...
I have setup the UART along the same lines as the sample project in the DevZone Academy. I have extended the example provided to suit the project needs.
What I am getting...
Hi all, We have a custom board running with a project based with ncs v2.6.0. On our board we have two external flash, one is used for DFU the mcuboot_secondary with QSPI and...
Hello All,
I am not able to find the nrf_drv_adc related files in SDK folder. ADC library is not supported in NRF5_SDK_17.0.2 is it so?
Thanks and regards,
Neeraj...
Hi Team,
We are testing the nRF7000's Wi-Fi location feature to enhance our device's capabilities.
Our setup includes:
nRF52832 as a BLE beacon
nRF9160 as a host...
When I follow exercise steps A to open nRF connect terminal,vs code will display issue as follow:
Whether some issues happened when I get nrf connect SDK?
How can I...
Hi community,
It's my first time building a board with a Nordic chip so for sure I've made a lot of mistakes. I made this with KiCad and uploaded all the files to the repository...
What is the possible reason that LED1 blinks and LED2 does not light up when the nRF5340 Audio source is operating?
I have read and understood the source code, but I am...
We've added our app's overlay files into the mcuboot child_image directory so that mcuboot is initialized with the proper state of the board. In our nrf5340_cpuapp_common...
Hello,
Using wifi monitor sample on NRF7002 DK, packet length is constantly 70. It was checked both by reading received variable from:
received = recv ( packet -> recv_sock...
Hi Nordic DevZone Community,
I am working on a project using the Zephyr RTOS with an nRF52833 series board, and I am trying to interface with an SSD1306 OLED display via...
I have a device with a programmable output pulse width for its data ready signal. I need to be able to reliable receive the pulse so I don't miss any interrupts, and I'd like...
Hi everyone,
We are using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. Our application collects data from a sensor via I2C and then sends this data to a smartphone via...
