Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
SDK 17.0.2, SD 7.2.0. with secure bootloader, when performing DFU without BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE, nRFConnect will successfully update the app. With BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE...
Dear all,
is it possible to get a more detailed explanation what the function "averaging cell search mode" activated by AT%XDEEPSEARCH=1 does?
Best regards,
Peter
I scan a few devices which have BLE_GAP_ADDR_TYPE_ANONYMOUS. When I print the addresses from ble_gap_addr_t.addr, they look like this:
AC:23:3F:77:28:AE AC:23:3F:77:28:AA...
Hi Everyone, I've started working with Zephyr, VSCode and nCS. I'm using a sample and working on it modifiying things, but I'm not able to include extern modules, lemme explain...
Hi,
I am developing Coap-Client and Coap-Server devices using nRf52840 dev kit. I am using ncs 1.7.1 sdk. I have a few questions.
1- I can successfully send a data received...
Hello all,
I have recently developed a custom board that uses an nrf52810. It also contains an accelerometer as well as some hardware for regulating the voltage and charging...
hi
I am using nRF5 Calendar example and
I have this problem
could you help me, how can I fix that?
I don't use the UART functions, I'm going to use SSD1306 to...
Hello!
I am currently working with Actinius' Icarus IoT board and I'm trying to get the interrupts to work. This is the boards' pin layout: At the moment I have connected...
Hi everyone,
I am trying to create a system to collect data from different sensors and store them in a FRAM. Then by using SPI, I want to transfer the data to the nRF52832...
Hi,
Trying to build the asset_tracker_v2 application I finally get the following error:
Rebuilding ‘zephyr / zephyr.elf’ from solution ‘build’ in configuration ‘Common...
Hi All,
I have problem running nRF5340 in continuous mode without any external trigger (timer/ppi). I would like to setup SAADC so that last conversion triggered new set...
I want to use CONFIG_UART_0_NRF_UART instead of CONFIG_UART_0_NRF_UARTE. But I don't get any option for this because CONFIG_UART_0_NRF_UARTE is selected by default .
I...
Hello everyone,
I am working on a project based on nRF Connect SDK v1.7.1 that I want to move to the new SDK v1.8.0. But I'm experiencing problems when building the project...
