Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hello everybody,
I'm currently trying to create a Bluetooth Low Energy Mesh network of multiple nodes that I can control using a Bridge application.
I use a nRF52840...
Hi,
we are developing one prototype where we are using two MCU for different task. we are planning to give common reset button (for customer access) for both the MCU using...
Hello,
I am attempting to create an example project of the Asset Tracker using the NRF9160DK.
I have installed SES using the Toolchain Manager.
I have attempted using...
Hi,
i'm using the nRF5340 DK and SEGGER Embedded Studio V5.50c. Today after starting SEGGER i was asked to perform a firmware restoration for the j-link if the nRF5340 which...
Hi,
I need to use two uarts for the project requirement. UART0 is enabled and working successfully. And I am trying to initialize UARTE, but I am not getting any output...
Hi,
I decided to try the “ble_peripheral/ble_app_gls” example on nRF52-DK.
While I could connect to the kit, pair and bond successfully, when I deleted the device from...
Hi:
I test this hids project, if remove the function bt_conn_auth_cb_register(&auth_cb_display). The iphone will require paired while reconnecting after disconnected. Can...
I am trying to determine the service handle of the nus example, to be able to verify that the central has turned on notifications.
I am using the sd_ble_gatts_value_get...
Hi,
I have a question about 'Thread Secrue DFU',according to the ' https://infocenter.nordicsemi.com/index.jsp ' ,the 'Thread Secrue DFU' does not use softdevice of transform...
Greetings,
CPU = nRF5340
SDK = nRF Connect SDK v1.6.1 and 1.6.0
Board = custom
For the nRF5430, we have a custom board that uses active high logic to turn LEDs on...
Hello,
I am trying to get the nvs driver working on the NET cpu and am having trouble getting the initialization working. The code below is what I am currently working with...
There have been several other posts on this issue dating back a few years, such as this one .
On Windows 10, if I am using SEGGER's RTT Viewer and I flash a nRF52832 with...
Dear,
As the example code is shown, I have been implementing on LED PWM through nRF53 GPIO0 12. If I set the brightness to 100, it was ON without any issue. However, if...
I use the "zb_sleep_now()" function in the main loop, which greatly reduces the start current. The device wakes up apparently due to the RTC2 interrupt used by the zigbee...
