Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I'm trying to integrate cli_libuarte on project that use FreeRTOS. I'm basing on example form SDK cli_libuarte how ever this does not use RTOS. What I'm facing is...
Hello!
I'm trying to perform DFU over BLE using a nRF52840-Dongle (PCA10059) devkit. I'm getting the following error:
I've tried to add '-cd 5' and '-f' options...
The OPS states the maximum transmitter RF power accuracy to be +/- 4 dB. Does this imply that if the power is set to +4dBm it could vary from 0 dBm to as much as +8 dBm? What...
The documentation is a little unclear. I am using Arduino Nano 33 BLE. Using the analogread() functions of Arduino I get a much worse performance than the nRF is supposed...
My application is composed by three different source code repositories, organized as follows:
+--- app
L---- lib1
| L-- src
| L-- include
L---- lib2
| L-- src...
This is a bug report for the NRF9160 AWS FOTA implementation tested with nrf-sdk at 25c4404f1
My application is based on the asset_tracker_v2 example.
When I initiate...
I am attempting to develop software for a wearable device that hikers/athletes will use in the case of emergency. It will send out an emergency message when a button is pressed...
Hello,
I am trying to use part of the code from this example https://github.com/zephyrproject-rtos/zephyr/blob/master/samples/subsys/nvs
to write to and read from flash...
Hi
I'm trying to use the battery sample to create some code that reads the battery level at boot. However I'm experiencing what I believe to be a race condition
If I run...
Hi Dev team,
I have been working on a Thingy91and I was trying to read out the battery voltage of the device.
I was able to do that through the modem using the MODEM_INFO...
I am trying to send just random dummy data to my android app. First of all, I am not expecting or need the confirmation, so I should be using the notification and not indication...
I have referenced the following document.
https://www.nordicsemi.com/-/media/DocLib/Other/User_Guides/nRFSnifferUGv22.pdf?la=en
I checked the contents up to 2.3.
However...
I have configured nrf9160 dts common file with one SPI3, I2C0, UART1 and UART2. Also i changed chosen section in the dts file to use UART1. When i build and run on nrf9160DK...
Hi, everyone on the community
softdevice: sdk17
I added the BLE_APP_UART peripheral function to the scanning project, but the device is wrong when the phone is connected...
