after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I'm doing a load test on radio. In 1Mbps mode, the transmission time of the radio with different loads.
For a packet size of 65 bytes, I used this test:
Use the logic...
The crux of the problem is that my Zephyr I2C port is getting locked into EBUSY, and
What are possible reasons for this
How do I fix it
Context:
I'm currently...
Hello,
I am using an I2C sensor with my nrf52832 board and if I do the sensor_sample_fetch(dev), I get an error code of -16.
What does that mean?
Is there a table to...
Hi, I am using BL653 module with nRF52833, I have an issue about using USB with normal voltage mode(I am using 3.3V external power supply).Do I need to left VDD_HV pin unconnected...
Can nRF51822 scan advertisements from other microcontroller(ESP32) using Arduino IDE? Recently I have been working with nRF51822 and could only code nrf acting as server ...
Shalom!
Our central BLE nrf52840 device continuously scans using a UUID filter. I can see that the UUID is matched in nrf_ble_scan_on_adv_report(). In my ble_evt_handler...
Hello ,
I have NRF thigy 91 and nrf9160 DK board and have flashed asset tracking hex file in both the devices .
But the thingy91 is not able to connect to nrfCloud but...
Hi,
Some of purpose we want to terminate current connection and rejoin to exit PAN.
I use zdo_mgmt_leave_req to request for leave. However , at callback , the status...
Hi,
I use FDS to store some data.
After creating the file, update the data using fds_record_update().
When the update is completed, FDS_EVT_UPDATE occurs in FDS_Event_handler...
Hi,
I read data from FDS and output it to nRF USB. The output is implemented by
app_usbd_cdc_acm_write (&m_app_cdc_acm, m_tx_buffer, (sizeof(m_tx_buffer));
But I only...
I've been going through the nRF Mesh SDK and want to integrate it with my Zephyr project.. Reading through the various blog posts and documentation, it seems that the Mesh...
Hello
I'm learning the nRF5340 using the purchased nRF5340DK. After completion the beginner's tutorial advanced to the Getting Started tutorial on BLE custom service for...
