Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am in the process of porting application code from the old nRF 15.x SDK to the new zephyr based ncs 1.5.0 SDK and would like to do all hardware configurations in...
Hi Nordic Team,
We've been long waiting for FEM support with multiprotocol and it seems like it is finally here with NRF NCS v1.5.0.
1- Can you please clarify, yes I can...
Hi
I tried to add the function of FEM to the Peripheral_hids_keyboard example according to the guidance of the link below. But it looks like it failed
https://developer...
hii this is rohit vekariya from bluesys lighting solution.
i am new in nordic can you provide example code for drive neopixel(ws2812) using nrf52832
thanks
I set up nrf52832 that it is proxy device, i create a loop that proxy device sent 20 message to app phone (Android) within 100ms. But my app (Android) receive only 1 message...
I'm designing the nRF52840 into a new product with BLE, LTE and GPS.
Could you please point me to a recommended matching network and antenna solution for the nRF52840? ...
I connected a button to LED on a breadboard, how can I write a debounce function to control a button. I checked app_button.c but it seems buttons they are using is button...
Hi, We have a custom design using an nRF9160.
We can connect and program the device using a jLink though the debug port.
How can we connect the LTE link monitor to the...
Hello everyone,
I get the following error whenever I try to build an application for the thingy91_nrf9160ns board:
The secure version works just fine.
For some...
Hi Team, I have design wireless node for biomedical application. I have used nRF51822 module in my PCB. I want to see the real-stream data from sensor (connected in input...
I am getting an error like this. I did not understand what it meant. could you help me please?
<error> app: ERROR 8 [NRF_ERROR_INVALID_STATE] at D:\1_1_xxx_xxx_xxx\V.1.5...
HI:
I Use the Projtcet: "......\nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c".
In the BLE_Central project, how to set the Tx Power??
thank you very much...
Hi , when i first recived my nRF5340 DK it had an preinstalled code that maked the leds to fade depending on what button i pressed, but now when i try the example codes on...
Hi,
We're running the aws_iot example and it would seem that by default it does not use the certificates in the file certificates.h
Is that the case and how can we use...
