Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
It has been said that Nordic SDK v4.1.0 for Thread is in maintenance mode. I was told that I should move new Thread development to nRF Connect SDK. I am trying to explore...
Are there any examples of libuarte enabling both uarts in the nRF52840 at the same time? I have been trying now for a full day and keep having problems with what options to...
Hi,
I have an app based on freertos_hrs example (nRF52832, SDK14.2)
I'm trying to get it into low power(sleep) mode, however the idle task keep on running and the system...
Hey all. I was testing DFU over USB on an nRF52840, SDK 17.0.2 and I can't seem to get the actual application to run after a successful DFU. I generate my own keys, use them...
Hello,
SDK51 appears to be an inconsistency with how various BLE related events are handled in the SDK. Multiple BLE event handlers may be registered using the NRF_SDH_BLE_OBSERVER...
I'm currently implementing a DFU "controller" in C on the nRF9160 for performing serial DFU with the nRF52840 and believe I have discovered a bug.
My firmware image was...
Hi
I'm using nrf52 DK with SDK V17.0.0
Currently, I'm using Single Buffer to send Data through BLE.
However, I want to use Double Buffer instead of using Single Buffer...
I might be dense here, but please bear with me and clarify something. I am looking at the SPI bus as drawn on the nRF52840. According to the schematics (PCA10056 - nRF52840...
Hello,
Background: I have a custom board that contains nRF52832 module and exposes UART pins (RX, TX, RTS, CTS). I have developed an application using nRF5 SDK v17.0.2....
I'm using SDK 17.0.2 And I found that when the Scan timeout is not working,
Debugging I found that when the nrf_ble_scan_on_timeout function is called, the source of the...
I have an nRF5340 development kit. I can flash a custom application into the app processor. However, when I try to flash the peripheral_lbs sample, I'm getting the error shown...
The hrs.c has the following code.
/* Heart Rate Service Declaration */ BT_GATT_SERVICE_DEFINE(hrs_svc, BT_GATT_PRIMARY_SERVICE(BT_UUID_HRS), BT_GATT_CHARACTERISTIC(BT_UUID_HRS_MEASUREMENT...
I have added the following modification to "ble_app_hids_mouse" example for pca10040 s132.
I want to add a peer whose IRK is known as follows,
void peer_add() { memcpy...
Hello, guys.
We are have nRF52840DK board and Zephyr NCS 1.4.2 development environment.
I am trying to include two PWM channels in the code and control them independently...
Still haven't seen coded phy support with nRF Connect for Desktop for receiving advertisements. With the fact that support from devices is slim, how are we suppose to test...
