I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I have an si7055 i2c temperature sensor connected to an nRF52840
I've tried my best to get a reading, but failed.
Therefore given up.
I'd be grateful for some help to...
Hi,
We are starting a new development for an Ultra Low power product.
Thus, we found the nRF9160 as a good option with its ARM-M33 subprocessor. However, we have some...
Hi,
I'm having trouble with the BLE_GAP_EVT_DISCONNECTED event. I have an nRF 52832 running the SDK 15.2 as peripheral and have tried several devices as centrals (not simultaneously...
We are using the Zephyr IIS2DLPC driver to talk to that sensor from an nRF5340. This driver uses the Zephyr GPIO API to configure interrupts, which is implemented in drivers...
Hi,
I want to use nrf52840 dongle as a provisioner to provision other server and client nodes. So, i was trying to program dongle by using seggger and building and running...
Hi,
I am currently trying to create a bootloader for a project I am working on. I am familiarizing myself with the dfu and bootloader modules by running one of the example...
Currently I have implemented Central using nrf52810, SDK 14.2 / Softdevice S132.
I want to know how to do OTA upgrade in Central.
Or I would like to get an example currently...
What's the proper way to turn off BLE to conserve power?
I have a board with DC power input and battery backup. When the DC power fails, I want to finish what I'm doing...
I have an nRF 52832 running the SDK 15.2. I have a few general questions because I'm seeing behavior I don't understand and doesn't seem to be right.
If I erase all the...
I am attempting to load up the default NRF project "AT_Client" located at ...\ncs\v1.4.2\nrf\samples\nrf9160\at_client project, however, whenever I attempt to load it with...
Hello
I studying the nrf9160 , is it better to use the UART interface versus the SPI and do I need to use the flow control ?
Thanks a lot
Stephane Boudaud
Hi,
We developped a custom NRF9160 board and it works fine, it connects to LTE-M. We then designed a new version of the same board by adding few things (like NRF52833 MCU...
The sample code at ncs/nrf/samples/nrf9160/mqtt_simple is not connecting. I dod not make any changes to the ode. I am using NB-IoT. LTE is connected. The link monitor, LTE...
I just spent hours trying to use TTM with nRF52840 and I wanted to share the fix:
You need to use the Thread FTD CLI (USB) pre-compiled binary from v4.0.0 of nRF SDK for...
