HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hello,
I've been trying to get a Thingy:91 to connect to the nRF Cloud from Shenzhen, China.
The modem is updated to mfwnrf9160120 and the firmware is on thingy91_nbiot_dfu_2020...
Hello,
I Have a custom PCB with Fanstel BT832 module soldered. Because that module does not have a 32 KHz quartz I need to set use the internal RC source instead. The problem...
Hello,
I am trying to understand if I am able to use the SPI pins as GPIO when SPI is not being used. This post says that we could be able to use I2C and SPI pins besides...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
am use SPIM . I...
I have an issue in buttonless dfu,I have 2 kinds of device,one has issue in dfu,another one has buttonless dfu and works well, I transported DFU code form another kind of...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am in the process of RF certification.
I downloaded the example at "nRF5_SDK_16.0.0_98a08e2...
I tried in vain to connect my nRF51822 eval board with LIS3DH using SPI. Currently I am using the SPI example in PCA10001 with spi_master_init and spi_master_tx_rx function...
Is there an issue with my clock that's causing the BLE not to advertise? The debugger seems to an error on the gatt_params_init() function, which should mean its a RAM address...
Dear BLE mesh Experts, We want to provision and operate a mesh network using an app that is running on various phones. The idea is to use a single phone during installation...
hi Forum. I'm working on a project with nrf52840 + S140 + TWI (SDK v16). Got all working separatly on my custom board, i.e. softdevice alone works fine and TWI also works...
Hi,
I'm trying to implement Install Codes on our project without good results: The end device could not join the coordinator network after retrying several times.
Because...
Hi All,
I need to send HCI commands from my uC to nRF52840 (with DTM firmware) via UART to for example set channel, Tx power, packet type etc.
Are there any examples/documentation...
Hello,
nRF52832 BLE project using SDK 15.3.0 and SoftDevice 112 v6.1.1. Circuit has the output of a comparator connected to two GPIO pins (COMPARATOR_PIN1, COMPARATOR_PIN2...
Hey guys, I'm currently working with NRF9160, developing code that requires a work-item to be scheduled within a time-frame (timeout value) that could go up to >24-hrs. I...
Hello,
I am using nRF52840 S140 v7.0.1 and using ble_app_blinky. I have a query on Secure Serial DFU if there is a change in Flash and Ram address.
In original example...