Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi All,
I want to implement a function to send data from the internet coap client to nrf52840 DK coap server. The nrf52840 runs .hex file which is one modified from Nordic...
Hello, I'm testing an example of a zigby light bulb with a nrf52840 (pca 10056) board.
Here, when I press "BUTNERT 1" on ZED, I want to send the [ON/OFF] status of the current...
The average current during the nRF9160 test DRX is 2.2mA. The period of DRX is 2.56s. Using a China Mobile IoT card. I am testing on the DK board and have turned off all peripherals...
I used NRF24L01 to transmit the data without ACK mode. The receiver received the data normally when only the WR_TX_PLOAD_NACK instruction was used to send the data.If the...
Hello,
I want to set a GPIO Pin to high. Therefore I wrote the code below.
But when the software is written onto the nrf52811, I can not messure any voltage.
I do not...
Hi,
I am going to do data communication between two boards with libuarte. I see that both txdata and rxdata should be uint8_t*. But if I try to transmit the char*, will...
Hi On a nrf9160, I need to send data via UART(E) at 921600 baud. According to the UARTE BAUDRATE register documentation the register value 0xF000000 (Baud921600) leads to...
Hi,
I changed application main.c to enter in to DFU mode after 20 seconds. System is reset every 20 seconds and the boot messages are printed. The message "Booting (0x8200...
I am trying to measure distance with a vl53l1x sensor through the twi_sensor example. I uploaded the code to segger by referring to sparkfun, but twi_handler does not work...
Hi
using sdk17, softdevice132...
There are some parts of the central implementation that I don't understand.
It is based on cle_uart_app_c.
Isn't the function bl_nus_chars_received_outprint_print_called...
It is amazing how common this error is - there must be 100 posts. Yet none solve the problem and none explain it. It suggests that there is some serious work needed to improve...
I've been developing using nRF52840 using the nRF5 SDK. I have also been using FreeRTOS in my projects.
I recently received an nRF5340pdk to evaluate the nRF5340. I have...
Hi,
The CPU at my target board is nrf52840 and SDk16.
Condition 1: It causes system lock at <-A-> (function of strlen at nrf_ble_scan.c) if I setup the filter of NRF_BLE_SCAN_SHORT_NAME_FILTER...
I am looking to use the nRF9160 in eDRX intervals of 2.7 minutes (no PSM). The goal of the device is to be dormant until receiving a command to begin transmitting its location...
