after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
Is there any way to tell when the modem has finished doing a band scan? I would like to know so I can swap between CAT-M1 and NB-IoT for globally deployed devices. ...
Dear
I am try to perform an OTA operation on a dongle of nrf52840 by ble_app_blinky for PCA10059 project and light-switch server for PCA10059 project, which works well on...
I've setup SDK 1.4 with Segger, however I can't get the Asset tracker Application to compile. It seems to be building the SPM even though the project is setup to use the Non...
I use the template for pairing and binding. For the first time, after binding, for the second time, I bind again, prompting to reject binding. How can I match and bind many...
Hi,
I want to compile and run Mesh examples. I tried the Light Switch client, server and the Sensor server examples. All of them fail when the linker is invoked. All of...
Hi everyone!
I'm new in Nordic DKs and I have a new Nordic Thingy 91, I understand that it uses two chips: nRF9160 and nRF52840.
Maybe this is a silly question but, can...
I have a custom beacon application that is mostly idle. Before adding a timer, the current consumption was 3.2uA. After adding the timer, the current consumption jumped to...
So far I've use the nrf gatt module for setting MTU and DLE and seems to be working, however this module does abstract packets and maximum tx time in a connection. There are...
I have incorporated the DTM example into my application. It works as expected when I set the NRF_POWER->GPREGRET and then perform a reset sd_nvic_SystemReset() , then enter...
Hi,
https://devzone.nordicsemi.com/f/nordic-q-a/67024/nrf9160-questions-related-to-immutable-mcuboot-application
From the above thread i learn that MCUBoot is not that...
To get the GPIO binding I can use:
device_get_binding("GPIO_0");
1. I would like to know where in the documentation it lists the strings you can pass to that function...
I am debugging the GPS function and referring to the sample code of the official GPS. As for the code of reading GPS data, I have a question that is the way of obtaining GPS...
Hi,
We are facing some issues between our ble devices (ble version 5) and android mobiles using nrfsdk ("Android-BLE-Library") library. (Version 2.2)
We are able to connect...
I have used two sample applications light / light_switch from bluetooth mesh to get a device with 2 elements:
- generic on/off clent
- generic on/off server
I want to...
Dear Sir,
The target has a non-secure bootloader on it, I'm trying for DFU which has a secure bootloader pkg only. After initiating the DFU, nrf connect app sends successfully...
