Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I'm trying to run the https_client sample on an nrf9160dk, and it's giving me the following output:
*** Booting Zephyr OS build v2.3.0-rc1-ncs1-1440-g"020" !$#a 1...
Hello,
I have purchased this device to use as a BLE sniffer. I have followed this manual to configure the device as a sniffer:
https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3...
Hello.
I'm using a nrf52 dk (nrf52832) + GCC 9.2.1 (9 2019 q4 major) + WIN10 + CLION and I'm trying to build an example project using GCC.
I get the following error: ...
Hello everyone ,
I have question about saving the configuration of Friendship so-that after rebooting the SOC, the friendship's configuration restored without applying the...
Hi, I'm HongJae.
I'm developing a Bluetooth peripheral program with nrf52.
Briefly,
if I send a hexadecimal message(e.g 0x35), GPIO's are ON.
After 1 minute from...
hi,
I found a interesting thing：I use the output function to configure the P0.14（nrf_gpio_cfg_output(14)）. After configuration, the normal output should be low, but it outputs...
hello all,
i am using nRF52832 SoC in my project and my requirement is to write some configuration into internal flash when i flash the program using segger j link.
for...
Hello.
I am evaluating with nRF52833 DK board. I checked both peripheral/uart and ble_peripheral/ble_app_hrs.
Examples work each well on nRF52833 DK. I want to add the...
Hi support Team,
Following are my Questions.
1. Please recommend me three development boards from Nordic. I would like to build the mesh Network.For example one will transmit...
I am seeing a number of issues, but since they appear to be different, I will use different threads.
Setup: have gone to ble_blinky example to keep things as simple as possible...
Hi, i am new to the nRF52840, i like the features it has and i want to create a board using it. In the datasheet it is said to have 2 ARM processors and i want to use it as...
About 3.7V Li-Po battery on spec., can we read adc value from the battery using p0.04(A1) without external voltage divider circuits? In fact, 3.7V battery outputs 4V ,seeing...
Hi,
I'm now planning to test BLE AoA using nRF52833 DK. For now the DK doesn't have antenna array, so I plan to use an addon board like below:
Is there any link or example...
