I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
Hi,
I am using NRF52832 sdk 15.2.0.
I am trying to do a device firmware update by following this link: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting...
Dears
I listed my questions below. Thanks.
1. About GPS searching and fixing, I tried Thingy91 outdoors.
- When Thingy91 connected to LTE, did LED shall blue color?...
I have a nRF52810 project which initially used the ble_peripheral/ble_app_hrs from the enRF5_SDK_15.3.0_59ac345 as a starting point. I have changed to a custom service and...
I am programming using the glucose service example source. The example source does not send any context data, so I added However, when testing with nRF toolbox, I noticed...
I'm trying to connect to my local LTE network but I can't pass the yellow and blinking LTE step. I couldn't also run the Asset Tracker project. Please tell me if you are covering...
Im trying to connect Thingy:91 and Thingy:52 to my mac book pro using USB cable to use AT config commnads. In both cases I'm getthing the following messages in the log window...
Hello there!
I was trying to look up some default values to take an RF measurement and I was wondering what the default Tx power is for the Advertising portion of the app...
I've finally worked around some funky bugs that only appeared after updating to 15.3. In my app, I had to change my clock source to RC or SYNTH to make it work (was hanging...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Ok so I am trying to integrate SPI master and slave initialization code. I am very confused about legacy and non-legacy drivers and HAL. I am getting strange compilation and...
Hi,
i am working with nRF52832, i need to us sleep.it may be do somthing and sleep 40ms,rtc wake up it and do somthing and cycle.
i see the rtc example but it may be some...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I called "pm_init" to do "PeerManager". Then, a part of FLASH has been written to "DE C0 AD DE FE...
HI,
I compiled MQTT sample, and always got :
ERROR: mqtt_connect -60
timeout error.
It seems that it takes about 2 minutes to get LTE link connected:
LTE Link Connected...
https://github.com/takafuminaka/nRF52832/blob/master/i2s_ws2812b_demostration_planB/i2s_ws2812b_drive/i2s_ws2812b_drive.c
I read the documentation, but didn't really grasp...
