Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Dear Support Team,
We are working on nRF52832 based custom design. We had interfaced 3 different sensors (i.e. one with SPI and 2 with I2C bus mode) and sending continuous...
I am facing a strange situation with my app. After turning off all my peripherals and switching to the most minimal code, I see quite a lot of current consumption and that...
So I'm completely new to bluetooth and I've been trying to set up the nrf52 dk pc 10040, but I can't seem to find any recent tutorials to set it up and I don't know where...
I am running flash_fstorage_example on the nRF52840 DK with SDK 15.0.0
I am having some problems with the example, as below:
1. When I run the example and use the shell...
Hi, I am trying to do MQTT disconnect, but I am always getting an error. First I successfully connect to the MQTT server, then I send some data, and then I want to disconnect...
Hi, I've been trying to use the nRF52840 Dongle to act as Bluetooth 5.0 peripherals but I cant seem to configure them for Long Range (coded PHY) detection. I am currently...
I ran one of my 9160 DK boards for 10 days using the Asset Tracker demo. The Hologram SIM card site I used says data exceeded 1 MB, which I understand the limit. Although...
Hi,
I have been trying to print out the float values using the NRF_LOG_FLOAT_MARKER, and i am only able to print 2 values in a single NRF_LOG_INFO line. Is there a way to...
Hello! I'm following the nRF52 Dongle programming guide to adapt the USB examples from SDK 15.3.0 to the nRF52840 Dongle. USB CDC ACM works fine, and I managed to get half...
Hi,
Sorry to bother you in your holidays.I want to get an conversion every time by calling nrfx_saadc_sample( ) .So I had configure saadc like below.But I found the adc...
Trying to print floats with NRF_LOG functions always prints a value of 0.00000.
E.g.
float value = 123.456; NRF_LOG_ERROR( "Float %f\r\n", value );
prints:
ERROR...
when I try to run: pip3 install -r mcuboot\scripts\requirements.txt, it fails with the following;
Collecting cryptography (from -r mcuboot\scripts\requirements.txt (line...
I'm trying out DFU functionality using nRF52840-PreviewDK and UART transport
On this page there is a table listing all the different combinations that can be downloaded...
Hi everyone,
I am currently working on a project that requires ICM-20648 and nRF52832. Is there an I2C driver available for these devices? The end goal would be to display...
I am using Keil and nrf52 dev kit to write some UART over BLE code if I set a break-point in nus_data_handler() it cause a reset to run soon after stepping though some code...
