I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
We are using an NRF52840. After initializing a UART that uses P0.06-TX and P0.07-RX the following function calls fail: sd_ble_gap_device_name_set() and nrf_sdh_enable_rquest...
I am playing with the TIMER peripheral and I am seeing that I must call the function "nrf_timer_event_clear" in order to get the TIMER interrupt to stop firing once a COMPARE_EVENT...
As shown in subject, I tried to register many BLE services, DIS, BAS, HTS, and Custom Service. Then nRF52832(and nrf52840 preview) has stopped by an error of NRF_ERROR_NO_MEM...
I am working in nrf52840 sleep mode and it is working perfectly in system_off() mode, but while trying to wakeup from sleep using timer the device is not waking up because...
I am configuring the SAADC for Single-ended mode which I would think is a simple/common task, but my output from the ADC is very jittery. It seems to jump between a good reading...
Hi!
SDK15, s132, SD6.0.0, nRF52832
I have nRF52832 in central mode and some bonded HID devices and another nRF52832 peripherial devices.
Now in the my central nRF52832...
I simulated the balun of nrf51822 accroding to the referenced design of nrf51822 on the official website. However,it showed the differential phase of the balun was not 180...
Hello team,
We are using CPU NRF52832/810. We have followed the THINGY hardware for BLE Antenna with Ceramic Chip. Due to our range requirement more than 100 meter, we wanted...
DK : nRF52840
SDK :15.3.0
example code : nRF5_SDK_15.3.0\examples\peripheral\flash_fstorage
I watched that using nRF52840 DK is best way for develop nRF52811. So I...
Hi,
We have a product that uses nRF52832, we are trying to get the FCC Certification. We are using the RF test example to setup the DUT.
We are able to get the signals...
Hi,
I wanted to use Nordi UART service, the problem is that if I have no contraction with the device, it would not advertise after a definite time, say 180 Seconds, my devices...
I'm trying to connect nRF916 FP1 Preview DK to LTE-M network using LTE Link Monitor but it fails. Below is details about my firmware/software:
Zephyr OS v1.13.99-ncs2
...
