Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
morning guys ;
I wanna create a bluetooth pan using raspberry pi and beacon nrf51822 using ipv4 , i don't have problem with the raspebrry it works well and it shares the...
12.3 sdk
i have error when compile this project ''.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol SEGGER_RTT_printf (referred from main.o).'"
this error how...
Hi I trying to interface Accelerometer sensor LSM6DS3 to NRF52832 DK.
whether I need to change board configuration or any pin configuration.
Pin configuration that i have...
The reset button doesn't seem to work on two of my PCA10056 1.0.0 development kits, but works on two others, and works on some earlier versions.
I tested by running the...
It was working a few times, then suddenly I started to get these errors, which I only got previously when not running as root (perhaps because it did not have permission to...
Hi,
I am trying to process data from MPU9250 in MATLAB and I have converted " .mat " file to " .hex " file using Embedded Coder . Can someone tell me if that " .hex " file...
(1) I am using GNU C++ to develop my application with nRF5 SDK. I found the STATIC_ASSERT_SIMPLE and STATIC_ASSERT_MSG macros defined in app_util.h are not working with C...
When running the light_switch_provisioner example built on my machine, it crashes on an assert in entry_validation() in mesh_config.c:
app_error_weak.c, 95, Mesh assert...
Hi,
I've a Raspberry Pi, Node-RED, with a Thingy connected. I get a message payload, looking like this:
{"uuid":"dfb561bb7d69","characteristics":{"2a00":[84,104,105...
Dear Nordic experts,
While investigating some of my bugs, I had to look into the GPIOTE driver code, and I realized that it has some allocator for mapping GPIOTE channels...
Several answers from Nordic employees state the possibility of Secure Boot and a "Root of Trust" feature:
use of ARM TrustZone on nrf52840 for secure storage/trusted region...
Hi,
I'm studying the example code of "ble_app_blinky_pca10040_s132 ".
What confused me is I couldn't find how the "led_write_handler" is added to the service. There is...
The board is made with the nRF52832 chip and can not be scanned during the test. Could you tell me why? The nRF52 DK board functioned normally. The platform used a mesh light...
