Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello,
I am trying to estimate Battery life. I am using CR2032 with 230 mAH capacity. I am confused with the calculations.
As per excels sheet in below link, for 500...
Hi, I have strange problem using pc-ble-driver on nrf52 with heart_rate_monitor example. When I set advertisement data to be 16 bytes long, two of our testing phones cannont...
Hi,
I am using nRF52832 and I need to create a timer interrupt handler, which can trigger at 417us (microsecond). I am using Segger Embedded studio. Please, can anyone help...
I have a project which recently started logging the following error on boot.
nrf_sdh_ble: sd_ble_enable() returned NRF_ERROR_NO_MEM.
This is the only log message....
Hello
I have a simple Thread network with 3 nodes and I would like to send a provisioning request from one to the 2 others in order to get their IP.
I modified the Thread...
I will like to know if the nRF52832 is capable of working properly when placed in series with a 30 Ohms Resistor ( which is the battery resistance for our application) at...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I want to use I2S to drive the speaker,just like playing the prestored samples from sounds.h in thingy:52.
However,i can't drive the DAC by I2S.Is there anyone have...
I just got my nRF9160 DK. Unfortunately the out of the box demo didn't work:
LTE LC config ... [00:00:01.029,876] [1;31m<err> net_if.net_if_init: There is no network interface...
Imagine following use case:
Alice has a peripheral bonded with Alice's phone (central)
On the peripheral, Alice switches to a "guest mode" which disconnects from Alice...
HI
UUID scan filters are set and enabled.
I was capturing peripheral device MAC id via ble_evt_handler.
i was expecting filtered devices should be visible but when i...
HI
I am trying filter peripheral devices based on UUID while scanning. I have set, enabled the scan filters but still output is displaying all the peripheral devices irrespective...
Hi I am using nrf52832 board and SDK15.2 I have below requirement:
Nordic board should act as central as soon as it gets booted and scan for particular service if present...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I found this very useful Throughput Measurement Application for for Threads: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0...
