after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi Nordic:
I want to change TX power of mesh-sdk.2.1.1 light switch, I've follow
https://devzone.nordicsemi.com/f/nordic-q-a/34491/mesh-range-power-and-mode
and set...
Hi,
I have bougth one Nordic Thingy 52 and one nRF52840-DK. My idea is to communicate both via bluetotth.
For example, i want to capture the temperature adquired by Nordic...
Hi guys,
I am using the softdevice S120 firmware: s120_nrf51822_1.0.0-1.alpha_softdevice.hex
The error_handler registered when calling sd_softdevice_enable is called...
We are implementing a Nordic NFR52832 using the ARM mbed ble stack that leverages the Nordic SDK using a HID over GATT profile. Windows 10 seems to have an issue with this...
Hi all.
I'm trying to make a list of brands and models of Android phones that have implemented LESC. I appreciate any feedback and experiences working with LESC (numeric...
Hi There,
I just want to confirm which method is being used to perform DFU over thread (Single bank update or dual bank update), and can I perform DFU on Sleepy end device...
Hi,
I'm trying connect NRF 52840 width Intel AC 9260 Windows 10 Desktop/
When I compile and run any examples from nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral and I...
Hi,
when generating settings on windows using nrfutil on one project takes about 2 minutes and it swallows whole memory during the command.
The command i am using is:...
Hello,
I am trying to use nrf5280dk with RIOT OS and Contiki OS. I am following these steps to enable access to the device from os. https://devzone.nordicsemi.com/b/blog...
Hello, I have an nRF52 device with NRF_SDH_BLE_GATT_MAX_MTU_SIZE set to 512 and it accepts connections and the client sets the max mtu to 512. It is on SDK 15
When
an...
I am working on a project involving BLE communication, but I am quite new to BLE, so please be patient.
The project scenario is the following: I have a nRF52 feather board...
Hi Nordic team,
I try to use the secure dfu of web app and test this code： https://github.com/NordicPlayground/secure-dfu-web-bluetooth
but I can not test successfully...
Hi,
I am using STM X-nucleo-iks01a2 sensor board arduino compatible, so connected to nF52840 DK arduino header and want to read HTS221 I2C/SPI interface supported sensor...
I've seen other users on the DevZone have had a similar problem ( link1 link2 link3 ), but none of their solutions have been able to resolve my problem.
I'm using the...
