Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi everybody I have a couple of questions regarding power consumption for the nRF 52 DK Rev. 1 (nRF52832). I currently have an application where I sample 12-bit ADC data via...
I'm working on support for several custom characteristics that require long write support. I'm using the nrf_ble_qwr library, and I've noticed what seems to be a discrepancy...
Hello,
I have an nRF52 DK here that behaves strangely since a few days. Hardware id is 0xc7
When I boot it up with my firmware, sd_ble_enable takes around 2 seconds...
Hi
We have used DTM functionality in nRFgo Studio to carry out signal strength testing during the design stage. We now want to automated this testing in end-of-line testing...
Hello,
I beginner for Nordic board, developing small device using BLE.
I build softdevice, bootloader and application. I checked working DFU mode(via serial, not BLE...
What a software i can use for develloping a Bluetooth Profil Mesh (BLE5) ? Hello every body , i want to develop a bluetooth mesh profil and i don't known which a IDE i will...
Hi,
I make my first project with the nRF52832.
On my first pcb the bluetooth works fine, but this pcb was not fully assembled.
Now i have made a second pcb that is fully...
I need to create and update some data record, the record contains some data that will be updated sequentially or randomly. But the sdk does not execute fds_gc automatically...
I am reading through IETF RFC7668, IPv6 over BLUETOOTH(R) Low Energy . In section 3.2.2, it states the following:
At network interface initialization, both 6LN and 6LBR...
hi
I am really confused For Indoor Asset Tracking which is better Nordic Mesh SDK or Thread
I see Thread Supports Cloud connectivity.
Can the device based on nRF52840...
Hi @ll,
I'm still trying to get the Mesh DFU example up and running. I'm following the guide in the documentation. (Mesh Version 2.0.0: it's the same in 2.0.1 so don't worry...
Hello all!
I am working in a project in which I have designed my own PCB using the nRF51822 chip because is gonna be used for BLE applications.
I have some experience...
Dear Friends,
I am trying to use Interactive Pyaci , but facing following issue after issuing required command:
(mesh) mehul@mehul:~/workspace/nRF/nrf5_SDK_for_Mesh_v2...
hi
The Peripheral HRS Example has device address in nRF52 SDK
de:ae:dc:9b:cb
I would like to know where in the Code this address is Set ? Not able to find
