Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello everyone, I'm new with Nordic devices.
Actually wanted to get services correspondant to I2C slave addresses and registers.
I was thinking about using the SDK template...
i am using nrf52832 in sdk11. I am interfacing motion sensor and spi flash memory. Both motion sensor and spi flash shares spi lines and having different chip select pin....
Hello
I'm implementing light switch demo code, but while build client and server code getting error
Building ‘light_switch_client_nrf52840_xxAA_s140_6.1.0’ from solution...
Dear Nordic Team,
Thanks for supporting.
Now start to work with nRF52810 chip. Already i am worked on nRF52832 based projects. Now i want to know the s112 soft device...
The GTT was great!
And the Solar panel demo was impressive.
We are very interested in integrating solar panel with nRF52 on our upcoming BLE products.
It would be great...
hi...
i want to check how the sleep mode is working so i am testing with the simple uart program
here you can see the code .. ble_nus is not sending the data in ble_uart...
Hello, I am using SDK15.2 on nrf52 DK with SD 6.1.0 and having an issue in long button press action. The single press and long press button action work ok before BLE connection...
Hi,Sir
We are keyboard developers and manufacturers,and we are using nrf51802 based on nrfready_desktop_2_v3.1.0,Our keyboards products works well,but recently we noticed...
Hi,
I'm trying to compile a simple example (light_switch__server_nrf52832_xxAA_s132_6.1.0) for Bluetooth mesh with Segger embedded studio. I'm having a hard time to get...
In nRF5_SDK_15.0.0_a53641a code, there's such definition:
#define UART_DEFAULT_CONFIG_BAUDRATE 30801920
Which means about 30.8 Mbps.
But in page 345 of nRF52832's...
Hello,
I'm using a nrf51822 board as a DFU controller to update another board's application, the client board runs the bootloader secure example. When I write data to the...
This is almost certainly a noob (to nRF52840) programming question.
I have modified the peripheral/gpiote example to invoke an ISR on the falling edge of a pin signal. In...
I am trying to use the Sparkfun nRF52832 breakout board as a master in I2C communication. I am using Arduino IDE to program the module. I defined pins 24 and 25 as SCL and...
Nordic Support, Let me first explain what I would like to achieve. I am developing a line of devices that will act as GATT peripherals. I would like average current consumption...
I have a custom board with an nRF52832 (CIAA-B0), and I am trying to use the SPI Master.
When I use SPIM1 or SPIM2, the transaction hangs, but the same code talking to SPIM0...
