Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I would like to prepare a provisioning hex file for my firmware.
Can somebody supply an example how this could be made?
I'm using gcc toolchain, Eclipse and SDK...
Hello,
I am using sdk12.2.0 and pca10028 dk. I am using one code downloaded from unknown source. The code is used to store data in flash. When I compile through keil I don...
Hi,
i try to establish a communication between 3 sensors in the following way!
Node 1 should broadcast messages to Node 2 and Node 3 as Peripheral.
To establish a...
Hello,
I am using pca10028 and sdk 12.2. I have interfaced temp sensor with nrf51 and now I want to store that data continuously in memory of nrf51. I want to store min 4k...
Hello, I want to program and debug the nrf52840 device but I'm kind of stuck at the programing range/address issue.
I'm using my customized board so I doubt Nordic Semi...
First I register the address of the central device to the peripheral device. When I work with a single peripheral device and a single central device, I can send commands from...
I'm trying to understand the subtleties in a Gazell link setup with multiple devices and a single host.
The documentation in the infocentre suggests minimum timeslot_period...
Hi,
Just wanted to confirm what the average current measured by the PPK represents. So for example if I have AVG in average window as 2.5mA, is that only the BLE (i.e....
Hi,
I found a bug in ble_app_gls example from SDK_12.3.0 / s130.
If user enters a wrong passkey, the app ends in a app_error_fault_handler exception and the central keeps...
I think I found the source of many of my recent problem. The print in Segger is going crazy.
I found out that if I increment a simple variable and print it when I hit debug...
Hi,
I am using the nRF52-DK as a device like beacon encodded with the original code of "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\ble_app_beacon.
I want to change...
I am beginner of 52832. Current software is based S132 4.0.2 and SDK 13.0.0. Test platform is based on PCA10040.0
My problem is application can not start normally in merged...
Hello,
I am using nrf51 and sdk11. I have one code and I am trying ti build hex or bin file for this code. Now the code size exceeds and so I am trying to build using makefile...
I am learning about FPGA. I have question general question related to it.
Doc1.docx
A FPGA is connected to a 14-bit DAC and to an output amplifier. The DAC have a sampling...
