Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello,
I am doing a project using nRF51822, s130 and SDK 11. I have modified the example ble_ap_hrs_rscs_relay.
My problem comes when I try to update a notification...
Hi,
I am porting our application from SDK10 nrf51 to SDK12 nrf52. The application takes use of a serial console accessible over UART.
I notice the new logger module...
Hi all,
i am V11 sdk.
Task:
i want to send and receive data without connecting the nordic_uart example
i.e ble_uart eg is send and receiving the data when we press...
Hi all,
i am using V11 SDk,
my task:
One board should broadcast continusuly.
if there is any neighbour is broadcasting ....then that will capture those data too...
Hi,
I am working on adc module of nrf51,through adc i am taking data and storing it in array.now i have to crossexamine this adc data with the prestored data and have to...
We are trying to complete Bluetooth qualification on our Cycling Power Service (CPS) against the Bluetooth Test Specification (Document Number CPS.TS.1.1.1).
We fail the...
We have been working on a project that requires the following separate segments be programmed to the board:
softdevice hex file
app hex file
UICR hex file
...
Hello,
I'm currently porting all my C++ code from SD130 SDK10 to SD132 SDK12 and I also upgrading from device_manger to peer_manager.
I've noticed that in peer_manager_types...
Hello,
It seems that NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE has wrong documentation. In sdk_config.h it says:
// <o> NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE - Default Baudrate...
Dear Nordic Team,
Thanks for support.
I want to know the possible for nrf52832 act as a sniffer. If it is possible means i want to latest sniffer hex code.
Dear Nordic Team,
Thanks for support.
I have tested Current Time Profile sample application whenever connect with nRF connect APP the debug widows shows always "Current...
Good morning all,
We have a circuit based on 51822 chip.
We are currently trying to monitor some value from 0v to 24v from the analog inputs.
It's working, however...
I recently saw that SDK12.0 provides a Bootloader Cryptography module. I'm not certain after reading the documentation that this module can support my use case:
infocenter...
Hi,all. i want to use nrf51822 to generate a 3.3M hz wave,but i don't know how to do this.Can this chip reach so high frequency？Can someone help me? Thanks ！
I'm trying to implement context switching from handler mode to thread mode using PendSV. I set the PendSV pending bit inside an ISR with SCB->ICSR = SCB->ICSR | SCB_ICSR_PENDSVSET_Msk...
