Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Using the nRF52832 and SoftDevice s132.
If the application code disables the SoftDevice, then the application CAN erase UICR memory in the nRF52832 device.
The question...
I control a module over UART using app_uart_fifo. This module is controlled from nRF host by commands to perform things. This generally works fine but however, sometimes when...
Hi,
I write a code for the max6657 temperture via modifying the SPI MASTER Example. The function for reading max6675 via SPI is shown as follow
uint16_t readCelsius(void...
Dear Nordic Team,
Thanks for supporting.
How to calculate the battery voltage level from Eddystone TLM. Its always transmit 240mV.
I am using CR2302 3V battery.
...
Hi all !
Can you tell me if it is possible to flash a single nrf51822 ship directly or if it requires at least the minimum oscillator X1 in order to be flashed?
The...
Hello. I want only 1 to 1 bluetooth matching about nrf51822.
I want only 1EA central with 1EA peripheral matching.
I set as below.
1EA - Bluetooth Central - UUID...
Yesterday, I asked a question (so far, no one has answered) about how an OS upgrade on my desktop computer might have broken my ability to flash and run BLE apps on the nRF52...
Hi there,
I have two nRF52 Preview DK boards, SDK 0.9.1 and 0.9.2, and SoftDevice S132 1.0.0-3 alpha. Several months back I got the Bluetooth heart rate demo from SDK 0...
Hi,
i am trying to wake up the nrf52832 from system off with a gpio interrupt.
When the signal on my gpio pin 28 goes from Hi to Lo, i trigger a callback function in...
Hello all,
I'm building a project on the nRF52382 with the S132 (v2.0.0-4.alpha). The project includes a Central device (GATT Clients) that read and write to 2 peripheral...
Are there any specs available regarding the performance of the nRF52 ADC's internal voltage reference? Accuracy (%) and temperature drift (ppm/degC) would be good. I couldn...
Hello,
I'm developing proprietary radio protocol using nRF52 (not using softdevice) and would like to know if it is allowed to write NRF_RADIO->FREQUENCY register while...
Hello, I've got a problem with an app_timer
starting from the BLE_UART example, I've set
#define APP_TIMER_PRESCALER 4
#define CLOCK_CONFIG_LF_SRC NRF_CLOCK_LF_SRC_Xtal...
