Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
My setup is as follows
1 Gyroscope + Accelerometer
1 RTCC
1 SPI Flash device
I want to set up the PPI to periodically sample the MEMS devices and the RTCC...
Hello,
I am trying to remove the use of the frame pointers for bootloader_util.c because I am getting the error : "r7 cannot be used in asm here", but I only know how to...
I use nRF51822( BLE nano) central mode to connect annother BLE nano (ibeacon mode), then I call disconnection to the peer address. Sometime, the disconnection callback will...
hi,
i am trying to send data using ble_uart app.
in this app i am using timer difference to send data. when i am getting 1st data in uart event handler. when i am printing...
I would like to implement DFU OTA updates without the Master Control Panel, and I have a couple questions:
Is there example code for the client-side of the DFU service...
Our personal phones are set to auto-update iOS apps. Unfortunately our team all got the latest version of the NRF Toolbox app (v2.5) released on February 5th, 2016.
Previously...
hi,
i want to execute a block of code in which timer should start. and stop at end of the block. and the timing depends on manual interrupt. and restart again when the execution...
Im using a board that is not one of the officially supported nRF51822 boards. Im trying to get the ANCS example project to work, but It wont broadcast or even turn on the...
hi,
i want to append data before sending. i am using ble_uart example.
here suppose the data is available on uart buffer at 1data/sec. i want to sent some timer/counter...
SDK 4.0.0-2.alpha
When run garbage collection, sometimes invalid offset on new page is present.
Adding next string fix this.
m_swap_page.write_offset = FDS_PAGE_TAG_SIZE;...
Hi everyone,
somebody recently told me that the PWM library as part of the current nRF51/5 SDK (v10 or v11) is more like a hack?
Since the docs fail to mention specifics...
I would like to know whether the amount of connections for BLE is limited by BLE spec, chip or stack (soft device)?
Also, same question regarding the possibility of the...
Hello,
I need to change my advertising Message periodically. In detail message (A) is sent in every 100ms and message (B) ist sent every 3000ms.
I defined 2 timer: ...
I noticed the nrf52-DK pca10040 comes with different ic revisions.
infocenter.nordicsemi.com/index.jsp
Where can I buy the pca10040 and be sure I got the latest in revision...
