Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
if I set BLE_GAP_CONN_SEC_MODE_SET_OPEN, I can get data,
but if I set BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM,
Three different even sequences happened, only one sequences...
Hi,
I disconnect the BLE by calling *sd_ble_gap_disconnect*(), and found that it run to *app_error_handler*() after the BLE_GAP_EVT_DISCONNECTED event occured, and I don...
I program the nRF2727 module with the "Block readback of mainmemory" seleted using nRFgo studio tool.
After that, I can still read out the content of flash. What's the root...
As per this thread: devzone.nordicsemi.com/.../question-regarding-hfclk-control the SD stack takes care of HFCLK, however as fas as I understand HFCLK is also responsible...
Hi,
I use the DTM for the production test, I use the transmitter test ,with canal 19 (frequency = 2438MHz).
What is the tolerance of the frequency do you recommend (Min...
Hi all
i am working on Student Response System in which there multiple Transmitter and one Receiver and i want Receiver(nRF24lu1p) to behave as HID device.
Can any one provide...
I just buy a set of nRFgo starter kit . One pin of the display module (nRF6350) was destoryed, and the correspoding hole of P6 in the motherboard was inserted with short pin...
Hi,
I have some questions about how BLE scanning works that haven't been answered clearly anywhere I can find, (except no-doubt the Bluetooth Spec/Tome):
What...
You can not build out " the arm c c + + compiler has stopped working " in Keil uVision5.
PC of lenovo made in (Windows7 environment ) ,
By introducing development environment...
Hello everyone,
thx in advance for answers.
there is limitation written for 6.0.0 as follows:
Synthesized low frequency clock source is not tested or intended for use...
Hi everyone,
Is there any information about the (approx.) amount of erase/write cycles the nRF51 flash memory can handle?
I'm using the NVMC to store large buffers that...
hi:
when use the gzll for host, the power consumption is large, about 12mA , but the device mode just 38uA. I find in host mode the main loop always be awakened even if there...
Hello,
I am using nrf51822 for couple of my projects and most of the time doing OTA device firmware update using development dongle connected to my Macbook Pro and running...
