Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I'm trying to measure message travel time using Gazel and k_uptime_get() so I can understand the packet intervals.
I'm using gzll_ack_payload_device and gzll_ack_payload_host...
Hello,
I am trying to control a PPK2 using my Raspberry Pi 3B+ running a 64-bit image of the Raspberry Pi OS (Debian Bookworm port) and I've been using python (v3.9) with...
Dear Nordic Team,
since the last release of NCS 2.7.0 the sd-card support breaks for me.
I am using the nrf5340 Audio DK with an inserted SD Card, and am running the zephyr...
Due to upgrading SDK2.5.0, I need to re-certify Thread1.3 in order to get a new CID for the previous module.Now I don't know exactly how to fill in the section of Thread Submission...
I have an application that requires invoking multiple commands to the same node in quick succession (multiple times a second).
To evaluate the feasibility of this, I flashed...
I am designing a pcb containing nrf52832. However, since I need a large number of GPIOs, I do not want to use the optional 32khz crystal in my circuit. But I also want to...
I'm using the nordic ppk II to measure the power consumption of my device.
In order to validate the charge (current integral) displayed by the PPK2 i put two PPK2 daisy...
Hello! I am an engineering student at KTH studying embedded electronics and I will be doing my thesis work for a company in about 6 months where I am supposed to be analyzing...
Hi everybody,
I'm just getting into Zigbee and try to follow the example at https://docs.nordicsemi.com/bundle/ncs-2.5.1/page/nrf/protocols/zigbee/adding_clusters.html to...
Good day
I have a custom board using an nrf9160 device. On the board I am running a variation of a lwm2m client. I have a question regarding a network connection. Why is...
Hello,
could someone point me where I can find the most current / state of the art example for the BLE UART app for the nRF25840 Dongle?
The version in the nRF5_SDK...
Hi,
I am working on a project which has external flash (FM25V01A ) connected to nrf52832 board over SPI. And when building the project, I am getting the following error...
Hello,
we run an application on a custom board with nRF52840 powered by an external power supply and buffered by a supercap. The supercap then provides the energy for the...
Hi,
I have 2 nrf52840-preview dk board. All of a sudden both the devices are not working any more.
I have referred to some suggestions and tried all the below cases and...
