Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am designing a battery-powered mobile device.
Previously, I was using Reg0 in DCDC mode, but I added an external 2.0V DCDC with higher efficiency (low Iq) and decided...
Hi!
I would like to know if anyone has any idea when we will hear more about the future products compatible with the new Bluetooth Core 6.2 specifications, as this will...
Backround: We are planning to use TF-M with a two-stage bootloader (NSIB & MCUBoot) using dual-slots for secure and non-secure images. We need to support configurable fixed...
To use ECDHE_RSA you need to enable the following Kconfig symbol:
This symbol depends on MBEDTLS_HAS_RSA_CIPHERSUITE_REQUIREMENTS :
This symbol depends on MBEDTLS_RSA_C...
I am developing a project for the Thingy91:X making use of the Asset Tracker Template.
Following the Getting Started guide, I successfully build for the Thingy91:X.
However...
Hi,
We have an existing nRF91 (nRF9151) project (NCS 2.9.0 ) that already includes multiple modules such as ECG, external flash, RTC, modem, etc. Now we want to integrate...
Hi Team,
I would like to interface the nrf9160 with nrf7001 by using the SPI. While building the WIFI-Scan example by using SDK 3.1.1. Even by using WIFI-shell example these...
Hi team,
I am experiencing a persistent MPSL assertion 1519 on nRF54L15 that occurs consistently at ~5 seconds after BLE advertising starts. The assertion indicates that...
Hi everyone,
I’m using nRF9151 with nRF Connect SDK 2.9.0. Without changing anything in overlay, prj.conf, or source code, several of my projects suddenly started failing...
Hi Nordic DevZone,
We recently acquired some Pro Micro nRF52840 Dev Boards ( link ) and were looking to use them with the nRF Connect SDK. The boards use a UF2 bootloader...
I have a question about the nRF54L15.
１．I would like to know the maximum number of devices that can be registered for whitelist and bonding.
２．I want to know how to...
I am having an issue where my nRF52840 Development Kit is not being detected by nRF Connect for Desktop , specifically in the Quick Start and Programmer apps. The DK does...
Hi, I have an Adafruit Feather nRF52840 which I'm programming using SDK 3.1.1. I want the following UART config but it is being rejected with error -134 which I believe means...
Here is a professional and technically detailed ticket template you can use to submit to Nordic Semiconductor (DevZone) , Quectel Support , or your internal System Architect...
Dear Nordic,
Could you please guide us how to set HCI_LE_Transmitter_Test / HCI_LE_Receiver_Test command?
Do we have to use Test mode command too?
Thanks.
