Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
When using the official Au Term.exe tool to perform SMP firmware updates on the nRF54L15 (NCS v3.1.0), if the tool is closed during an ongoing transfer and then reopened,...
Hello,
I previously completed a project using the nRF24LE1 chip and the nRF24LE1_24_SDK library. It was a simple 2.4 GHz two-way communication system using the basic predefined...
Hello
I am currently working with the nRF9151-DK hardware to perform tests related to PSM functionality on an NB-IoT network.
The main issue is that, although the device...
HI,
We are using the IM69D120 PDM mic for our audio application. I am able to interface the MIC and record audio with the NRF5340.
I have read the PDM data and stored...
Dear Nordic Team, Could you please help me to find the exact product which I can use to connect my two wire 0.37Wh 100mAh 3.7V 351525 Li-Po battery to the nPM1300-EK for battery...
I'm trying to combine two projects, C:\ncs\v3.1.1\zephyr\samples\subsys\nvs and BleFundamentalsL5E2 (Implement bonding and a Filter Accept List). They work fine independently...
We're developing an application using the NRF54L15. SWD will be connected to an external device that can update the firmware on the MCU if there are any issues, but we don...
I would like to evaluate the use of NB-IoT in the UK which Wireless Logic SIM included with nrf9151DK provides. Using the following sequence of AT commands I can send data...
Hello. Please excuse these potentially silly questions, but I've been given the task of monitoring battery charge while also achieving maximum energy savings.
A wearable...
I just got a NRF9151 dev kit and I want to build the image as non-secure, using: nrf9151dk/nrf9151/ns. The build is failing with error: C:/ncs/v3.1.0/nrf/modules/trusted-firmware...
Hi,I made a 52840 board ,it's p0.18 hanging, without connecting a 10k pull-up resistor and a 100nf capacitor to ground. I connected 3v3, GND, SWDIO, and SWDCLK from the 52DK...
NRF54L15 NCS 3.02
I have to change my BLE advertising from Legacy to Extended. Looking at the Zephyr example "advertiser" which compiles & runs fine, but I notice that behaviour...
Hi,
I am currently trying to connect a nrf52811 as an companion to an ESP32 user UART.
I am using the interrupt driven UART implementation as kind of the last resort....
How can I set a custom interval for *extended* advertising?
I'm currently calling bt_le_ext_adv_start ( struct bt_le_ext_adv * adv , const struct bt_le_ext_adv_start_param...
