Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
Our device nRF 52832 using connect SDK connects with the Android application. And successfully negotiates an MTU size of 247.
Is there any call back in the nRF SDK...
Hi!
I have three new nrf52840 dongles and I am not able to provision any of them. I load the code nrf/bluetooth/mesh/light (SDK v2.1.0) in one of them for the first time...
I am using the nrf52833 dk board with vs code , I have tried all the solutions that I could find on the already available asked questions, example https://devzone.nordicsemi...
SDK: nRF5 SDK v17.0.2
use example SDK17\examples\ble_peripheral\ble_app_uart to add DFU over BLE
SoftDevice: ANT_s332_nrf52_7.0.1.hex
MCU: nRF 52832
windows application...
Hello, guys.
I just wondered why use LTE Link monitor from nRF Connect make nRF9160 scan lte-m networks and even connects to it.
And when I'm trying to use external MCU...
Hello,
We are using this module in our new product and are in the process of Bluetooth certification. The BMD-350-a-r lists QDID of 101018, but the nRF52 family lists...
Hi,
We are using nrf5340 and nrf connect SDK V2.0.0
Using below code, we are able to scale up/down the processor frequency.
However, in our application we want to...
Hello,
I want to specific a hci event in zephyr RTOS when using nrf connect sdk. But I don't know how to achieve it.
In Bluetooth Core v5.2, vendor specific events have...
Hello,
I would like to create my beacon application to publish periodically (e.g. 10sec) data related to three temperature sensor.
What're the possible solution to implement...
Hi Team,
I am using nRF5340 dev kit and NCS(Nordic connect SDK 2.0.2)for my DFU POC purpose. I want to perform DFU update of nRF5340 through nRF USB port instead of the...
Hi developers,
Now, I want to get a correct Tx power value. I printed out the value from "ble_gap_evt_t->params.adv_report.tx_power" and could get only 127, even this...
Hi,
I am using 5340 but it's uart consumes a lot of power 2.01mA
SDK: NCS2.1.0
project: peripheral_uart
I have disabled all other peripheral equipment,put all...
when I open nrf connect for desktop i got blank page,
and there nothing in the console:
I've installed/am using:
nRF Connect for Desktop v.3.11.1
J-Link V7.68b...
Hello,
we are using the nrf9160 in one of our products. Our assembler has used old nrf9160 SICA B0 chips on our first protoyping round. When we run our software on the nrf9160...
