Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
hi
i'm new to the nRF platform and realised it uses zephyr. i come from a pic & stm32 background with little rtos knowledge and find the official zephyr cryptic. especially...
I created a BLE device with custom characteristic showing the sensor value (int16). But I can't achieve 1khz sampling rate.
1. Is sending data via NUS faster since the central...
I would like to using Keil to build secure_bootloader project for changing NRF_DFU_BLE_REQUIRES_BONDS from 0 to 1. But Keil failed to build. Please refer to snapshot of Keil...
Hi, I am using a third party module based on nRF52840. I want to use a standard UART to operate the CLI shell. I am not clear how to do this, any help?
Thanks,
Kaus...
Hi,
I am trying to run a sample "Beacon" that a sample of nrf5340 about bluetooth.
but, there is one issue as follow when i run each sample about bluetooth :
Bluetooth...
hi，
the project https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
if this project can't build in windows platform？
thanks...
nRF 5 SDK 17.0.2
I am working on getting the nfc_pairing_reference example application migrated to S140 on two nrf52840 DKs. I have successfully ported the hardware, the...
We have a customer interest in developing a BlueZ application using the nRF52840.
This will be using the ARM9 CPU Atmel SAM9G25.
These are some of the software versions...
Environment introduction:
1. Use software SEGGER Embedded Studio for ARM (Nordic Edition) V5.50a.
2. 52833-DK*3 And EK42442ds *2
3. Switch order ANT1>ANT2>ANT3>ANT4...
Hello Group,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I was...
Hello there!
We have different sensors connected to our custom nRF52840-based board running Zephyr OS. The goal is to transfer sensor readings to the PC by using a USB link...
The problem I encounter now is that NRF52840 is my MCU, and I need RS485 module to transmit data. The supply voltage of my NRF52840 is 1.8V. Is it recommended that the RS485...
Hello,
I am trying to do a single bank DFU update using nRF Connect app and have SDK 16 on my device. I have set NRF_DFU_SINGLE_BANK_APP_UPDATES to 1. Bot looking at postvalidate...
Using the NRF5 SDK V17.0.2
Once again finding myself struggling to understand the structure of the SDK as a result of lacking documentation, there seem to be so many layers...
