after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
It's mentioned in this forum that MQTT-SN may be implemented on nRF connect SDK. I would kindly ask if there is anything available about that? And will MQTT-SN be officially...
Hi,
I'm using SDK 14.2.0, and nRF52840-Preview-DK.
Followed the tutorial:
devzone.nordicsemi.com/.../
I've programmed the soft device from: ..\components\softdevice...
Hi, I want to use filtered list during BLE advertisement in out project. The flow is as follows: (I'm using nRF connect app for testing ble connection) 1. Just advertise so...
Hello,
We are trying to connect to an AWS MQTT broker using the nRF9160 with modem firmware version 1.2.3 and are not having any luck.
Project background:
Using...
Hi Team,
Setup:
Application: smp_svr with overlay-cdc.conf
Board: nrf52840dongle_nrf52840
NCS: 1.7.0
System: Windows
Tool: mcumgr
I am trying to upload an...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a BL653 dev kit. The firmware has a bootloader and it can perform DFU over...
Hello，I am using nrf24l01+ product for FCC certification, it requires a modulated carrier. If I send this modulated carrier in the form of data packets, it is not a continuous...
Dear ,
When i use the demo of ".\SDK\nRF5_SDK_17.0.2_d674dde\examples\peripheral\twi_scanner\pca10040\blank\arm5_no_packs", Some exception occured . The sdk enters dead...
Hi
I'm running into this error when enabling the soft device (see title). I've read about the PREGION[0] and that, if the info variant is > 0 it indicates a soft device...
when told the problem,I wanted to tell the you information . I use NCS 1.7.1 version,OS is windows 10,nrf connect for desktop is 3.10.
Firstly,I install the nrf for vecode...
The newest version that will run on my mac is 3.8. any never version will just freece at the startup window.
...but the programing app crashes when I try to add a file in...
Hi,
I am using the RSA sample code and I need to make the key persist. When I try to change the lifetime attribute to PSA_KEY_LIFETIME_PERSISTENT, the key generation fails...
Hi, I am developing a device using the nRF52832 mcu. I have written my application and have interfaced with an external I2C Sensor. It works perfectly on the NRF52-DK, I get...
I am using NCS v1.9.1 with the nRF52840 and I am not able to move the MCUBoot secondary slot to SPI flash.
I have been able to communicate with the device over the SPI...
