Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
Working with a nRF9160dk here.
Documentation states, that the GPIO_INT_DEBOUNCE flag should just be ignored when configuring a pin, if it is not available in the driver...
Dear Members,
Is it possible that I save a flag before sd_nvic_SystemReset();
in NRF_POWER->GPREGRET ?
And retain the flag after system reset ?
How ? any examples...
I'm using Windows and ble_app_uart example for my development.
I wanted to check log from my dongle so I'm trying to use log_backend_uart with putty.
But I couldn't get...
Hi,
I want to use a TSOP IR receiver on a custom board for sending different commands to my device through a remote controller. for example, if I use a Samsung TV controller...
I want to configure the NPM1100 to work with either rechargeable or non-rechargeable batteries (in factory).
Would it work to set mount a suitable resistor to the NTC pin...
Hi,
We are evaluating thread. And would like to build a basic demo app using a thread border router and a few sensors. We got the border router working with the coprocessor...
Hi,
I am using nrfconnect sdk with central_uart example. How to get the name of the device
advertise the BLE discovery packets? nrfconnect android app shows the name after...
Hej!
I see that the CRC block is used in the Radio under section 23.6 of nRF52832_PS_v1.4.pdf . Also, I noticed that the CRC32_ENABLED is only enabled in the bootloader...
My previous ticket is closed. I would need, but still help with the configuration of the pins. I report my last post.
Hello, I did some tests with the oscilloscope directly...
Hi,
The previous SDK would allow configuring radio notifications before the radio comms would take place.
I wonder if it is possible to get similar notifications on the...
i have a requirement to connect two nrf52833 boards to connect each other.
(1).if i turn on the Board1 should scan the bluetooth devices if any other bluetooth devices present...
I am working on a proprietary RADIO protocol on the nRF5340 device. Because I'm trying to squeeze as much throughput as possible out of the RADIO I would like to be able to...
I am developing my first BLE Server application with the nRF52832 and using VSC/nRF Connect/Zephyr ROTS. I come from a Cypress/PSOC Creator background, and am struggling a...
Hi DevZone,
I recently updated my version of SEGGER Embedded Studio for ARM to v6.20. Now, warnings that were not shown before are caught.
I want to ignore the warning...
