Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
hi support team,
i am trying to help customer on demo about 9151 dfu 52840.
currently, 9151 is using nrf_cloud_rest_fota demo and 52840 is using "zephyr\samples\subsys...
I am able to successfully perform a firmware upgrade on the Distributor itself. However, when attempting to upgrade the Target devices, the mobile app shows Upload Complete...
Using the latest version of nRF Connect for VS Code, how can I display all output lines of the build process rather than the “condensed” line overwriting version. This used...
I'm seeing a few of these errors in my uart evt handler
I cannot seem to find where these are enumerated in app_uart_fifo.c or nnrf_drv_uart.h or nrfx_uarte.h.
Question...
Hi,
I have just received 2 DK boards for the nRF54L15 and using VScode to build and flash the code onto the DK
The reflector is detectable on my phone and I can connect...
SDK: nRF Connect SDK v2.9.0
Chipset: nRF52840
I'm using ncsv2.9.0nrfsamplesperipheralradio_test to test the RF.
The initialization code is as follows:
At this...
We have a custom board with npm1300 seem below. Im loosing 3mA more than expected. I used npm1300 both Vout1 and Vout2 before in other project. Same design and copmonents...
Dear Sir and Madam,
Now we are trying to certify Bluetooth qualification for our wireless module used nRF54L15, we are considering how we can set TSPX_FAE identifier?...
Hi Team,
I'm trying to calculate CMAC using the KMU on the nRF54L15, but the `psa_mac_compute()` function fails with the error code `PSA_ERROR_NOT_PERMITTED (-133)`. I need...
I'm seeing garbled/malformed UART console output when running apps on the Thingy:91 X. This includes pre-built apps from Nordic and custom apps I build myself.
Here's an...
in my disc, C:\ncs\v3.0.0 is here. but in nrf extension, weclome page shows the button ("install sdk"). it looks find no sdk. I need set the path to C:\ncs\v3.0.0 (I do not...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi.
I made a board with nRF54L15. I would like to use P0.01 on nRF54L15 as GPIO output., but I failed to confirm P0.01 turn high.
Then, I asked nordic AI anything to solve...
Hi,
I generated the credentials as described on the webpage , but az_iot_hub_client_telemetry_get_publish_topic always returned devices/<some garbage characters> and I got...
Hello, For my project I need to control 3 gpios pins. I already found difficult to find gpios that were not already used internally. I decided to use the gpio0 - 8,9,10 they...
