Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am curious if the LE Power Control feature, that was added in Bluetooth 5.2, can be enabled in the Bluetooth Controller on the nRF5340. It currently doesn't show up in the...
Good morning,
I'm playing with samples on the evaluation board and things seems pretty good Now I want to test things on the product chip and not the evaluation board...
Hi，
I am doing a project with NRF52840, I can use Keil MDK to erase and download normally, but it cannot be recognized by NRFGO studio,。
I need your help。please~ Thankyou...
I have been using nRF Connect for Desktop and the Toolchain Manager with VC Studio for a couple of months on my Windows 10 machine for Zigbee development with the nRF52840...
Dear Nordic experts, This short code snippet is supposed to reset (unprovision) a Bluetooth Mesh node and reboot it (nRF5 SDK for Mesh 5.0.0): node_reset() is called at the...
Have a NCS/ZBoss-based Zigbee app running and I want to enable FOTA, and it was failing with missing app_update.bin file.
Thinking it might be something with my own code...
Hello All,
Maybe someone out there has done this - but is it AOK to swap +/- on the nRF52840 output so a -3.3V PWM signal can be generated?
Are there output zeners on...
Unfortunately it is only ever explained here how printf is possible via UART. I wonder how printf is possible over BLE. I would like to send messages (strings) with numerical...
Hello, we have a goal of getting the BLE MAC address from out NRF52840 devices during manufacturing and printing it externally on the device. I was hoping the the MAC readout...
Hello everyone,
I was wanting to perform FOTA on the nRF9160 DK, so I decided to implement the Application_Update example, I uploaded the app_update.bin binary to our...
I have an application where I need to count clock cycles on a GPIO input. I'm configuring a GPIOTE channel N to generate an IN EVENT on rising edge of an input GPIO PIN (the...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. Now it needs to add a function for deleting a "child node...
Hi,
I'm trying to set NFC pins as GPIO in my custom project. I'm using zephyr 1.8.0 SDK. I added the following line to my prj.conf:
CONFIG_NFCT_PINS_AS_GPIOS = y
...
