Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
The non-standard function mlme_rx_enable declared in the header mac_mlme_rx_enable.h does not seem to be defined in 802_15_4_lib_gcc.a.
The compilers throws an error: undefined...
Hi all,
I'm trying to put the system into the SYSOFF mode when the device detects an external charger. HW-wise it's implemented by the charge controller pulling a GPIO HIGH...
Hello,
Let me just briefly state that I have referred to required documentation and also executed spi_transceive_async() test, at zephyr\tests\drivers\spi\spi_loopback...
Hi
I want to use nrf52840 to develop a central like figure below，the central can connect and communicate with all kinds of peripheral. Is there a reference example？
Hello,
NCS1.8.0 Windows10 X64;
spi_loopback test,default code default pins;it is ok.
when i change the SPI_1 pins ，
Failed to achieve the effect, still used the original...
When setting up a pin to toggle on the RTC's TICK event through the PPI and constantly reading the RTC's COUNTER on the nRF52832, my team observed frequent glitches on the...
Hi All!
I am using the cloud client example. The development board is nrf9160. This example works well and sends the message to nrf cloud on button press. Is it possible...
I'm using the Nordic Python libraries to receive the BLE data. I can send the data from our board with the nRF52840 chip on it. If I send the data to my Android phone with...
Hi.
In order to save battery in an "advertising only" peripheral, would it be possible for this module to remain in sleep status and start advertising (for a preset period...
Hi all,
i am using nrf5340 with SDK v1.5.1
I want to know if it is possible to use nrf5340 as central and peripheral device simultaneously?
The application is -
1...
chip : nrf52833 softdevice : s140 nrf52 7.2.0 IDE : IAR OS : windows 10
I try to USB DFU in nrf52833 I'm using secure bootloader base on secure bootloader example and...
I have a project with a nRF9160 and using its LTE modem to connect to a LWM2M server, based on the eclipse Leshan. I am using the lwm2m_rd_client. I have noticed some problems...
I try to integrate mcuboot and BT DFU into my application. I'm using SDK 1.8.0 and DK board nrf52832.
My problem is, that i got this message "Unable to find bootable image...
