Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
We've been using nrfjprog with no particular issue for a while now. Usually to fully flash a chip (whether it's for a complete re-flash or for a new chip) we run those...
I am mid-way through development with the nRF52840 DK and Zephyr using the VSCode extension. I'm using v1.8.0 of the SDK.
I am looking for advice on setting my configuration...
Hello Community, I'm using the current sensor INA219 with NRF5340dk. Communication is through i²c protocol and using nrf SDK v1.7.0 . I'm trying to get the data output (Voltage...
Dear Sirs,
I'm referring to PDF files or html links to get detailes information about nRF_Drivers and nRF_Libraries for Segger Embedded Studio to manage the ARM Core resources...
Hi,
I am using "otCoapSendRequest" to send data to my coap server.
Inside the callback, I am using otMessageRead, to read the response.
But my code crashed inside otMessageRead...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
The question is, is it possible to GATT communicate with each of the multiple...
HI
I am traying to convert library max30105 arduito to Nrf52840 code but i have a problem about this
I am reading de Reg FIFO led red and led IR , but its not the same...
Hi I'm currently using the sample py script which is given in https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nordic-thingy52-raspberry-pi-python-interface...
Hello Nordic Team!
I'm working with the nRF52832 and following this tutorial from Nordic to do OTA DFU: https://devzone.nordicsemi.com/guides/short-range-guides/b/software...
OpenThread and MCUBoot don't play well together anymore of the nRF5340 with the release 1.8 of the nRF Connect SDK. Flashing :
results in the bootloop with I assume is...
Hello,
I am a beginner in nRF. I want to implement EEPROM. So I am trying to execute Zephyr/sample/driver/EEPROM code but I am getting compilation error the below error...
Hello,
I am new to BLE. I am currently working on a beacon application. I have used the beacon example code from SDK and modified it. I am using SDK-17.1.0 controller is...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to simultaneously send advertisements with different cycles, communication packets, etc.? If so...
I've been tinkering with my Dev Kits (3 @ nrf52840-dk and 1 @ nrf5340-dk) as I try to find the right software/hardware architecture for my use case.
I made a lot of progress...
Hello , i am developing drivers for a spi ic , which by using spi example i wrote the drivers they are working fine , also i am able to run and modify ble uart example according...
