Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, I want to be able to send 1bit of data with as low latency as possible, what is the best way of doing this? Can i in some way directly control the low level of the radio...
Hi All,
i am using the below link to flash the bootloader
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/device-firmware-update-dfu-with...
Hello,
I am using Eclips & ARM tool chain for project with BLE functionality. I tried to import this code in Segger embedded IDE but it did not worked. This project is old...
Hello,
I built peripheral_hr_coded sample and looking into the partition manager report (I trucated the output):
What are the s0_pad and s1_pad?
What are the EMPTY_0...
Hello,
I am developing a FreeRTOS project that uses nRF5340 MCU. For the inter processor communication I would like to make use of the RTOS-agnostic RPC library (sdk-nrfxlib...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.7.1
Zephyr version: 2.6.99-ncs1-1 (commit...
Hi:
I have a BLE HID remote control that needs to be connected to the HID central(nRF52832).My SDK is NCS v1.8.0.
When I try to connect with the HID remote I get the log...
Hello,
I have to make the external flash on the nRF9160DK work with the nRF9160.
From what I understood, the default settings are that the external flash on the board...
I have beacon that broadcast its name with type 09. I cannot get it while scanning of nrf_uart_c (adv_report).
I assume I need to activate scan_req and then parse the response...
I need a constant acquisition time for my SAADC. In my experiements I see jitter in the acquisition time, so I started debugging with PPI to ensure no Interrupts are making...
Hi,
I am trying to enable event length extension on uart example provided on the sdk. I look for information on how to done it and i found links like that:
https://devzone...
Hello，
I am using ncs1.7.1, qspi + mx25r64 external flash ota it works well, but I don't know how to change qspi to spi.
I need your help thanks
I change the parament...
Hi Nordic,
I am working on a raspberry pi based gateway which has Thread Border Router and edge node functionality. I have setup the OTBR on the gateway and I have manage...
Hi,
how can I change the standard LED_0 output from P0.17 to P0.03? I am using SES, toolchain 1.8.0 and the nRF52DK board and I would like to flash the sample code to a...
