Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
In our design we use Fanstel BM832 module, based on nRF52832 chip. We have failed spurious emission in ETSI RX mode. Rx LO at ~4958 MHz exceeds the limit by 0.3 dB....
Hi,
We are working on the iOS App development for our BLE device. Our query is that, “we have completed the connection with Ble device with our iOS application on first...
I am using a setup with a PCA10040 with the PPK as piggy back. I also use a JLink Ultra+ connected to the "Debug in" connector on the PCA10040. I have cut the SB20,21,26,27...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I had tried to advertise in TLM format (in temp variable) of eddystone value coming from sensor ssts751 integrated with my devkit but not getting correct. Please suggest me...
I use nRF5340 DK as Central, iPhone as Peripheral.
I start a scan with no filters and in scan_filter_no_match() I check if RSSI is good enough " RSSI > -40 " and initialize...
Hi all,
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My development board acts as a slave, while an app that tries to connect...
Hello,
I'm struggling to understand the available RAM size in that chip.
After reading the product specification v1.7, the RAM specification is described as follow:...
Hi,
1. When nRF5340 has no power supply, adding 3.3V power supply to the digital IO port will produce voltage drop.
2. Why does the voltage drop occur?
3. What is the...
I'm trying to port a project from nRF52832 SDK15 to nRF52833 SDK17.
As a first step, I'm trying to get the HRS sample to work, as my other project was based on it. So far...
Hi,
I am trying to decide whether to go with the NRF5 SDK or NRF Connect SDK for use with the NRF52840.
From the compatibility matrix documentation at Infocenter, I can...
Hi,
I'm looking for a solution to update my program with BLE. I need to do it with a mobile app developped in Flutter. I found the Flutter library to flash the Arduino ...
I have a master device and a slave device. The slave device has 6 characteristics, 4 of which are notif. I need to use the master device to obtain the data of these 4 characteristics...
Hello,
I have just bought a nRF5340-DK. My board is labeled 2.0.0, and appears to use a 2nd nRF5340 as the debugger. I am trying to use TF-M with a Rust application. So...
I'm using Linux 20.04. I have been following the manual installation guide for setting up the nRF Connect SDK and also nRF Toolchain
in my .bashrc file:
export PATH=$...
