Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi
I am looking for a ways to perform DFU over serial, surprisingly i dont find any ways except this thread with no answers
https://devzone.nordicsemi.com/f/nordic-q-a...
Hi all:
About with the nrf_desktop example in NCS ,
I would like to modify the CONFIG_BT_HIDS_MAX_CLIENT_COUNT to '2' ,
so I add below command at "app_ZDebugB0.conf...
Can someone tell me the correct cable to connect the two boards together for debugging purposes.
There seems to be two main options, but its not clear:
TC2050-IDC-NL-050...
Hello, I experience some issues with NRF9160 and eSIM card. SIM_1V8 always output 0v and "AT%XSIM?" return "%XSIM: 0". I want to know if there is prior software configuration...
hello all,
I am trying to find the best power efficiency to transferring a pack of data(30 byte each time) from one nrf52 to another nrf52. I have a 80 uA in average power...
Hi all
So i had a working running example on SDK Thread and Zigbee V3.0.0. This flavor used the softdevice s140_nrf52_6.1.1_softdevice.hex I've migrated to the new SDK...
Hey All
I've found thread, dealing with this problem here: https://devzone.nordicsemi.com/f/nordic-q-a/77775/nrf_ble_lesc-nrf_crypto_ecc_key_pair_generate-returned-error...
I try to connect my nrf5340 CoAP server via my border router with CoAP Messages (with the IP address) from a computer. Is that possible? And if so, How?
I made a border...
I want to read peripheral's characteristics value in a fixed time interval or an event-based in the central.
I am using the nRF52840 Evalution board and SDK_17.0.2.
Here...
hi Support team,
Customer tested mesh SDK4.2, and now had one question:
their product is end node, and once button pressed, MCU is waked up and send the message to server...
in the gps example, there is a struct
nrf_modem_gnss_pvt_data_frame
in which contains the accuracy in meters, by documentation definition, it's /** Accuracy (2D 1...
Hi,
Facing some issue in creating sample application in vscode
nCS sdk V1.7.0, created sample hello world project and added build configuration for bl653_dvk
getting...
Hello all. Now I am making a BLE network with multiple peripherals and central based on NUS. How could I make data transfer between the central and specific peripherals? I...
Hello,
I would like to develop OpenThread applications that run under ZephyrRTOS for the nRF52840 processor. It appears that there are 3 possible development approaches...
Hello I'm trying to implement the DFU Trigger library into my project. to get following function:
" When the trigger library is added to an application, it allows a connected...
