Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
https://devzone.nordicsemi.com/f/nordic-q-a/65059/buttonless-dfu-on-nrf52832
When I try to DFU from NORDIC_BUTTONLESS , nRFConnect disconnects from it and connects to DFUTARG...
Hello,
I get an error message when running this function:
int ret = i2c_reg_write_byte(data->dev, cfg->i2c_addr, LSM6DSOX_INT1_CTRL, test);
I know 0x0BAE0002 error means...
Hello, With nRF5 SDK 17.1.0 release a new ifdef NRF_BLE_LESC_GENERATE_NEW_KEYS in nrf_ble_lesc.c has been added. Could you please clarify what the intention is of this generating...
Hello Team Nordic,
I think there is still a problem in the SDK 17.1.0 if not using a Softdevice (with SD all is OK):
in "nrf_drv_clock.c" -> "nrf_drv_clock_init(void)...
Hello Nordic team,
I am building an IoT solution and plan to use the nrf9160 just as a stand alone modem. App will reside on a separate MCU and talk to Nrf9160 on uart...
HI,
I am developing weight scale with Bluetooth feature. I have already developed the code to get weight scale reading using SPI example.
Also tested ble_app_uart code...
Hello,
I have currently cloned and built the latest master branch of Eclipse MQTT-SN Gateway https://github.com/eclipse/paho.mqtt-sn.embedded-c.git on my Nordic Border...
Dear N ordic S upport Team,
After I updated the nRF Connect SDK (1.4.0 to 1.5.1) and the Modem firmware (1.2.2 to 1.2.3) on my nrf9160 DK devices, the date time isn't synchronized...
Hello there,
It is actually basic for the Bluetooth connection for the nrf52840 using Zephyr, which changed the scan filter by name based on the central UART sample.
As...
Hi there,
We are currently using IAR embedded workbecnh IDE for our development on non-Nordic products. We are thus considering the possibility of also porting our Nordic...
Hi Nordic Support,
I am getting zero distance value from sensor(vl53l0x). I used SLAVE_ADDRESS =0x29 and register address=0x01. My code is mentioned below
void data_handler...
We originally saw (and reported) this problem with nRF5 SDK 4.1.0. We switched to nRF Connect SDK 1.6.0 which did not exhibit this problem. Now we just tested with nRF Connect...
Hi, I'm trying to found a way to flash production config for a project based on zigbee NCS example with OTA. Is nrfutil still a valuable tool for creating a production config...
Hi.
I'm trying to emulate my project, which is intended to run in either nRF9160 or nRF5340 boards (both using Arm Cortex-M33 processor), using QEMU, but as far as I know...
