Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am currently working on a project that requires to sample a 50Hz sine wave and transmit the data point over BLE, which will need around 10 - 20 samples per cycle...
Hi There
I’m hoping to implement a low power always-on/listening (response time <10s) industrial product in the UK
I’ve spoken to several acquaintances and had conflicting...
Hi All:
We are using nRF52840 SDK with BLE Mesh sdk5.0 to develop bluetooth mesh and we can use light_sw_client to control the LED1 state on the light_sw_sever via BLE Mesh...
I am using PC code derived from pc-ble-driver heart rate collector with a nRF52840 dev board
On adding characteristics sd_ble_uuid_vs_add() I get an error of 4 - NRF_ERROR_NO_MEM...
I have an nrf52832 acting as a central device that is trying to connect to a peripheral. However, after the peripheral disconnects and the central tries to reconnect I get...
Hi,
I was looking at this page https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_modifying.html and saw the following line:
"When building your application...
I am getting an NRF_ERROR_CRYPTO_RNG_INIT_FAILED from nrf_crypto_rng_backend_init during the sm_init sequence. Any suggestions on what might be causing this?
Hi Sir/Madam,
Our project needs to use TEE on nRF5340 which seems to be implemented by TF-M for now and future. After investigating the implementation, I didn't find a...
Greetings,
What is the minimum low pulse required to externally reset the nRF5340?
I see this answer for nRF51 and this answer for nRF52 . Can I assume nRF53 will be the...
Hi,
I have a nRF9160 DK and Iam trying to join my Private NB-IoT network that my company has (So I can get a static IP). I have the NB-IoT activated Nano SIM and the credentials...
Hello,
I've seen the other threads about this topic but they don't seem to be that helpful.. I'm using a BL653 board with the nrf52833 chipset.
Yesterday, I was able to...
Hello,
I am trying to flash a custom software to a NRF52832 DK.
The DK is powered by USB and i've connected as follows :
VDD(nrf) to Vref(J link)
SWDIO to SWDIO...
I'm developing a central that may have to service more than one peripheral concurrently while (occasionally) advertising its own peripheral service. Things seem to work OK...
