Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello, I have a question. In the HID_keyboard routine, I have already bound two phones.
Now I want to cancel the binding, and the function was called by key interrupt pm_peers_delete...
Hi,
I am new to the zigbee development and currently going through the documents.
My end goal is to develop a application that measures the level of a tank using radar...
Hi
We are using an external 32MHz crystal to generate the internal 64MHz clock.
As described in several examples, we start the HFCLK with
NRF_CLOCK->TASKS_HFCLKSTART...
Hi,
I am using nRF52840 and SDK 17.0.2. I used to write data using nrf_fstorage_write() at some address of Flash and I want to read the same data using nrf_fstorage_read...
Hi Nordic,
We created a firmware based on the eddystone example in nRF5_SDK_17.0.0_9d13099,
I modified the macro APP_CONFIG_ADV_INTERVAL_MS_MAX in es_app_config.h from...
Hi,
After connect, we add services/characteristics, and call sd_ble_gatts_service_changed(),but it also return BLE_ERROR_GATTS_SYS_ATTR_MISSING. I have enable NRF_SDH_BLE_SERVICE_CHANGED...
I'm struggling to get my nRF52840 DK to appear in nRF Connect (3.6.1), but I have no issues with connecting the nRF52840 Dongle.
I have been using this hardware for a couple...
My aim is to use a nRF52832 for a Bluetooth peripheral device.
- I just started with a fresh SES V5.44 and downloaded the nRF SDK 17.0.2 - I imported the example "ble_app_hids_keyboard_pca10040_s112...
My product needs HMAC using sha256.
I looked at the \nRF5_SDK_17.0.0_9d13099\examples\crypto\nrf_crypto\hmac
It has been written for nrf52832. My product uses nrf52810...
After the call is initialized and started (nrf_drv_pdm_init nrf_drv_pdm_start), the callback is executed only once. It needs to be re-nrfx_pdm_buffer_set each time in the...
Dear friends,
I flashed a mesh serial example and fetched the Composition Datacomposition data by composition_data_get(), as below code:
I wonder the meaning about the...
I have implemented nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_beacon\pca10040\s132\arm5_no_packs code for iBEACON.
I am able to run it and able to see the advertised...
Hello,
I was using the send example which is located in C:\v1.5.1\zephyr\samples\drivers\lora and trying to send a message to an Arduino LoRa gateway.
However, I found...
