Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I try to execute the PWM settings via the library in an extra .h/.c file to keep my main method as small as possible. Unfortunately the program sticks in the ErrCheck and...
I am currently designing a circuit with the NRF5340. This circuit will be alternatively supplied by VUSB when connected to a USB port and by a 1.8 V power supply to VDD when...
Hi,
I am using nrfconnect to debug my application code. i have an application code with 9 services in total and it is working fine as expected.
Now the problem is, if...
I have a freeRTOS based system and my Logging Thread, which is based on the examples has odd behviour when used in conjunction with the WDT. When I first program the board...
Dear Nordic,
I am adding the NUS to a firmware that already runs a custom service. I based my code on ble_app_uart. It fails during init, when it calls ble_advertising_init...
Hi guys:
a. I use a uart dfu bootloader(loacation: SDK-location\nRF5_SDK_15.0.0_a53641a\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_uart) in 52840 soc...
What is the ADC internal reference voltage (0.6V) tolerance at room temperature and over the full operating temperature range?
Or is it same as the value specified in the...
I am using NRF52840dk boards to make an openThread mesh network with CoAP. There is an example in NRF-SDK for coap client and another example for coap server. I used them...
I know there is an ongoing global semiconductor crisis. In the products, we decided to switch to NRF52/53 family products as core MCU. However, we're having hard time getting...
Hi,
Currently our system is using printf() to print some debug messages to the Segger debug terminal. Now we would like to reroute these messages to a UART port.
We are...
Hi there,
My nrf52840 DK seems dead. I want to recover it.
What I did:
Put the nrf52840 DK into Bootloader mode by pressing the "IF BOOT/RESET" button while powering...
Hi,
I'm working with pc-ble-driver and a PCA10040 devkit.
First, the central sends a data length update:
This returns no error (0), and on the BLE_GAP_EVT_DATA_LENGTH_UPDATE...
Hello,
we have a question about the usage of FDS. The data to save has a length of 1200 words. So the virtual page size is set to:
#define FDS_VIRTUAL_PAGE_SIZE 2048...
Hello,
I am using "pheripheral heartrate" example on SES, but I can not integrate SPI or ADC. How can I add "nrf_spi.h" and "nrf_adc.h" and relative C files on that project...
