after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I connected my device over BLE with the computer and currently using Bluetooth LE Console from Nordic. The Console is receiving data and that is good, but I do not know how...
I'm running the radio_test example on an nRF52840, but when I try different modulation duty cycles, it seems to work fine for everything less than 94% however 94% itself starts...
Hi Nordic,
I got the following error when I start nrf connect the first time under MacOS. This log is captured by turning on the Debug console:
Uncaught Error: dlopen...
Hello,
I am sampling two analog signals at different sampling rate with burst and oversample enabled.
nRF52832 (Rigado BMD-350)
SDK 15.2
IDE - Segger Embedded Studio...
Hi,
I just got my custom nRF5340 board and started testing it. Here's what I've done:
Connect the board with JLink v11.
Erase the board with Programmer on nRF Connect...
Hi I trying to develop a module in the 52810. I want use te ble_app_beacon and add a DFU buttonless. I was able to add the DFU, but when i was to integrate the buttonless...
Hi, i am Karls of Gabsjin in south Korea.
Sometime ago, i happened to know something controlled by mobile(smart phone)
So I would like to make a avr circuit controlled...
Hi,
I built a peripheral unit which working on NRF52805 with SDK17 (S113/S112).
The unit needs to be "multi peripheral" and advertise 2 different advertising packets simultaneously...
Hello, I have a strange problem and I am not sure how to approach it.
The problem is that the connection sometimes does not get established. This issue appears on Android...
Hi Nordic,
I am been investigating SES these days, may I ask how to export the settings in SES, such as indent settings, text color theme, etc?
I have there laptops need...
Hello,
I'm working with NCS on a nRF5240 based BLE device.
On the BLE side I want to do something like this:
Connectable advertising
Phy: 1M
Interval: 200-500ms...
On my own board ,I just connect VDD and VDDH pin don't connect anything, Now my board can not use ble fuction,if I can confirm it's not the software issue, so is it possible...
Hi,
In short, my problem is that my code works when I execute it inside one event handler, but doesn't work inside another event handler, and I don't understand why it fails...
