Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
I'm trying to configure nRFgo studio, but after connecting the device to my PC via RS 232, nRFgo studio can't recognize the com port.
Where can I find a user manual...
I'm working on pca10059(nRF52840 dongle) to send UART data over bluetooth to another device.
My test environment is,
Arduino Uno to send uart signal using "mySerial.write...
In nRF5 SDK for mesh v5.0, what kind of information (related to provisioing and communication) is stored in the internal flash memory?
And what is the API for accessing...
Hi , I have real ECG device with 2 Click and I almost got NRF52840 with PCA10056 development board. I want to put the analog signal from the ECG device to the ADC on the development...
hi support team,
customer is using 5340 1M i2c interface, and we find out that ncs 1.5 still don't have 1M driver, we have to modify the source code，may i ask the when R&D...
Hi,
I am saving temp data along with timestamps in the internal memory and sending it through ble.
if during transfer the queue becomes full (NRF_ERROR_RESOURCES), I am...
Hello all,
I'm developping a firmeware to test the bluetooth inside of our case. So i want to start DTM with a bluetooth command.
The command goes right, but the dtm_init...
We are switching between two modes of ADC sampling in our application:
single shot - Consists of a routine -> Init saadc -> convert a sample of one ADC channel -> uninit...
Hello,
I am trying to implement the workflow "Application as the manifest repository" as described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...
Hi DevZone,
We are trying to move our existing application from SEGGER compilation to a GCC build for CI / CD purposes. However we are seeing a strange bug with uint64_t...
Hi, I use an NRF52840 in my product. The NRF52 is interfaced with an external module in UART. The NRF52840 is always powered by the battery using the different power mode...
Hello All,
Working in lift industry, I recently recovered a BLE project developed by an ex-colleague running on LairdBL651 using with nRF connect SDK 0.3.0 (nrf52810, Segger...
Hello
I am using app_pwm control. When creating PWM, I am using the code as below, can I put float value in period?
I think I can only enter INT value at the period...
I have cloned the BLE code from the periperal_uart example provided in the SDK. However, I am using C++ so I am perform my BLE initialization inside a .cpp file (i.e. main...
Hi,
i'm trying to compile the asset tracker v2 for the nRF9160-DK but i get the following error:
"opening dependency file modules\mcuboot\boot\bootutil\zephyr\CMakeFiles...
