Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
Looking at Readme in NCS Zigbee sample NCP, it says "You can change the communication channel from the default UART to nRF USB".
Similarly, after enabling multi-protocol...
Hi,
I have an nRF91 Thingy that arrived last week but it's not operating as expected. I've downloaded the latest version of NRF Connect and I've been following the get started...
Hello,
I am a beginner student and I think this is the kind of misunderstanding on my part. I program on the Thingy 1.4.0 with the SDK 1.4.2. I create my own project to...
I am using the nRF52840 (with SDKv17.0.0 + s140_7.0.1) and have an issue when I create a file using FATFS (when disconnected from the PC) and afterwards copy it via USB (Windows...
My NRF52840 based module BT840 powered by one Coin cell with 5sec.on and 5sec. off with battery life of 22 hours . Can you help us in extending battery life ? Thanks Regards...
Hello ! I'm currently experimenting with the direct test mode for the nRF52840. I got it up and running with the nRF connect application.
I do however want to run it from...
I'm following this guide from Nordic to set up GCC and Eclipse to develop with Nordic SDK for the nRF52840. I'm going to develop for the SparkFun Pro nRF52840 mini development...
Hi,
I am able to sniff the data from nRF52840 DK in windows 10.
But unable to do it in Ubuntu as per procedure mentioned in sniffer guide.
No Interface is shown in...
Dear Support team,
The nRF52832 chip supports NFC. But I wonder if the chip has the capability of passive operation without battery and just energy harvesting through NFC...
I am evaluating the SAADC options and I'm looking for sampling one input at fastest speed. Easy DMA looks promising, but my function for SAADC communication hangs, if I set...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) using device: EYSHJNZWZ (nRF52832) connection device...
Hi,
Reading through IPSP posts on devZone I realize there's IPSP support in nRF5.
Wondering if there is IPSP (router role) support in NCS - for nRF52833 target?
Hi all,
in my project I have a nRF52DK and a nRF52840DK. I will use the nRF52DK as peripheral and the nRF52840DK as central. For this I flashed ble_app_uart on to the peripheral...
Dear Members,
How can I define my solder mask properly ?
Is my solder mask definition correct ?
Please have a look on my screen shot, thanks
On the PCB
The design...
I am following the MQTT example provided https://infocenter.nordicsemi.com/topic/sdk_nrf5_v16.0.0/iot_sdk_app_mqtt.html?cp=7_5_0_4_2_4_6 with nRFSDK 16.0.0 and nRF52DK
I...
