after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I am trying to create an application that uses the mesh light lightness [client/server] model using the example application as a guide and I have a few questions...
I want to check which version of BLE is implemented while using a particular SDK or Soft Device(SD). Is the version of BLE dependent on SDK or SD or both ? I couldn't find...
Hi,
We encountered a problem if we take off the battery during functionning.
The UICR Register is completly erase when we put back the battery.
The issue is with lost...
Hi - I have a MDBT42Q SoC board developed by Seeed Studio which contains the nRF52832 SoC. The board is powered as the image below and I can program the board through the...
SDK: nRF5SDK Toolchain: ARM GCC
Hello,
I have some devices out in the field using nRF52840s, using the non-SoftDevice bootloader, and a custom mechanism for reading updates...
While the nRF5 SDK offers great support for validating the SoftDevice and application firmware in internal NOR Flash on every boot, it looks like that's not the case for the...
I am using nrf52 DK board with SDK15.3.0 developing my application on top of ble_blinky_peripheral example .
How do add CTS service in my application ??
I have refered...
Hi
I want to make use of this SD-card reader together with the nRF9160dk.
From what I understand:
1. I need to create a nrf160dk_nrf9160ns.overlay file to chose which...
Hi,
As in the subject, I cannot find where to change the optimisation level. I am working with the Zephyr bluetooth sample project - peripheral_hr.
I have found a previous...
Hi
I have register the esim of iBasis and its works relly well but I need know how to use a esim of a different company on nRF9160DK, I don't know if the location is important...
Hello,
I'm using a modified version of the examples->peripheral->radio examples from nRF5 SDK v17.0.0 to receive packets sent on Bluetooth Low Energy channel 37 using...
I use ble_app_uart_c.
I have a central(nRF52DK). I have a peripheral(nRF52DK). When i run my code, I would like to see my peripheral's name and it's UUID on the terminal...
I am using SDK 16.0.0, Soft Device S132 (v7.0.1) on a custom nRF52832 board.
I have a secure boot loader on board that is triggered by a buttonless OTA application.
After...
Hello. I'm in the midst of purchasing a power profiler to works with nRF51 Development kit and nRF51 USB Development Dongle. May I know if all the technical resources on nRF6707...
