Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi All,
I have been using the fatfs examples to write data to a SD-CARD Using SPI, Up until now I have been able to use effectively, as per the documentation I Understand...
I don't know how to manage the Bonding key. I confirmed the following sequence, but it is abbreviated as "Keys stored in keyset". At what timing and how should I get and save...
Hi guys,
I am creating an application that can enable my device to measure the voltage and temperature, after I am able to send these data via BLE to my mobile app (nRF...
hello Nordic
i am working with nrf52832, sdk 6.0, softdevice s132 v7.0
i read around the forum that i can advertise a beacon packet every 20 ms
but in the ble_app_beacon...
I was using MBED TLS crypto library for various cryptographic stuff and hashing. It was working fine with SDK 1.2.
I tried to port my code to latest SDK 1.3 and I am having...
Hello
I'm now going to read PD_SCK and Dout from Hx711
but i can only get the value from PD_SCK, no value from Dout
here is my code, using NRF52810 and HX711, hope someone...
I have currently building and am running the SPI Transaction Manager Example (spi_master_using_nrf_spi_mngr_pca10040) on the nrf52 pca10040 board, where is information for...
hello Nordic
i am working with nrf52832, sdk 16.0 s132
1. i see when i use the app_time i have to initialize it using this line of code :
though i thought and...
Hello, I updated a working project based on nRF52832_xxAA 32Mhz crystal, from SoftDevice S132 5.0.0 to 7.0.1, (set preprocessor NRF_SD_BLE_API_VERSION=7)
now the sd_softdevice_enable...
Acctually, I use nRF5 SDKs for transferring IMU sensrsor data via bluetooth to mobile app. When I check the license of source codes, the components kiibohd controllerv0.5...
Hi all, I swear I've read every post under the sun regarding this, and tried so many different things from all of them that my project is probably slightly screwed now. I...
Hello!
I am trying to run the experimental ble_app_hrs_nfc_pairing example from SDK17.
I am using an nRF52832 module and SoftDevice s132.
The example compiles fine...
Hi! I'm trying to get a basic example to show the 9160 going into the System Off mode and then waking up when a button is pressed. However I have not been able to get the...
