after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am using the gazell protocol of nrf52840, How can I specify the correspondence address of this different handles when I USE A HOST to communicate with eight handle devices...
Hi,
I have looked at the different post regarding the nRF9160 and SPI, but I can not get it to work on our custom board.
Attached the board definition files.
Here...
I have the Thingy91 plugged into a macbook pro(osx catalina) with usb.
I have updated the firmware on thingy 91 with the precompiled application and modem firmware ( 2020...
We are able to form a openthread mesh using CLI-ftd examples.At present we have server communicating to Clint in UDP portal .Is there is any UART command which is meant for...
Hello.
I am using SDK v17.0.1, nrf52833.
I can enter DFU Mode with pressing Button 4 and reset Button.
However, I want to enter DFU mode without any Button.
I've...
Hi everyone,
I'm starting from USBD example and I want to implement a composite device.
If I want to implement a composite device I have to add one interface and then...
I'm working with several Samsung SmartThings and I am wondering if a call to will address this the issue of devices leaving the network insecuely https://www.samsung.com/sg...
Hello everyone, The last few days I was advised to buy the nrf52840 DK. Up to now I have worked with the dongle. I read online the need to download the j-link software. Where...
Currently, I'm switching my platform form nRF52 to nRF53.
For the work I'm doing, I need to use DPPI to enable GPIO events to trigger SPI transmissions, without interrupting...
Hello,
Looking for some background info for SOFTDEVICE ASSERTION 0x0002715e. sdk 15.3, SD s132_nrf52_6.1.1
Maybe related, there is no Assert if fds_record_write() is done...
Hello
I am developing devices including nrf52832 and 3.3v buzzer. However, the buzzer in this device is very hot and the battery is running out quickly.
Now I know that...
Hi. I always appreciate to your kindness and fast reply.
I want to extend BLE range from 200m ~ 500m using FEM.
For the first time, I choose SKY66111 but it is not working...
Design background and goals,
1.Both ble_central and ble_peripheral are used nRF52832.
2.All nRF52832 UUID are the same.
3.Devices of different groups can’t be connected...
